Impact of different chemical denture cleansers on the properties of digitally fabricated denture base resin materials
Journal of Prosthodontics · 2024-08 · 33 (7) · 691-699
DOI: 10.1111/jopr.13761 ↗Kurz gefasst
Vergleichsstudie in der Zeitschrift Journal of Prosthodontics, 2023-11. Verfasst von Ramy Abdallah Abd Elrahim und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Dental Biomaterials, Faculty of Dental Medicine, Al-Azhar University, Cairo, Egypt. Hauptthemen laut MEDLINE: Denture Cleansers, Denture Bases, Surface Properties, Hydrogen Peroxide. Die Arbeit wurde bisher 16-mal zitiert (Crossref) und nennt 44 Literaturangaben.
Abstract (Originalsprache)
Purpose
To compare the impact of three different chemical denture cleansers (CDCs) (Corega, chlorhexidine, and hydrogen peroxide) on the surface roughness, microhardness, and color stability of 3D‐printed, computer‐aided design and computer‐aided manufacturing (CAD‐CAM) milled, and heat‐polymerized denture base material (DBM). Materials and Methods A total of 420 disc‐shaped specimens (10 ± 0.1 × 2 ±0.1 mm) were fabricated using three different construction techniques: three‐dimensional (3D) printing ( n = 140), CAD‐CAM milling ( n = 140), and heat‐polymerization ( n = 140). Sixty specimens (20 of each DBM) were used for baseline (pre‐immersion) measurements (T 1 ) for the tested surface properties (hardness [ n = 10/material] and roughness [ n = 10/material]). The remaining 360 specimens ( n = 120/material) were investigated for surface roughness, microhardness, and color change after immersion for 1 year (T 2 ) in distilled water or CDCs ( n = 30/solution and n = 10/test). The data were analyzed using two‐way ANOVA, one‐way ANOVA followed by post‐hoc Tukey's test at a significance level of less than 0.05.
Results
Significant differences were observed in the effects of the tested CDCs on the surface roughness, micro‐hardness, and color stability of varying DBM specimens ( p < 0.05). Corega showed the highest surface roughness and color change in all DBMs while H 2 O 2 resulted in the lowest microhardness for all DBMs. The lowest changes in all tested properties were seen with distilled water followed by chlorhexidine. A significant effect of type of cleanser, denture base material, and the interaction between the two was seen on all measured properties ( p < 0.05).
Conclusions
The tested CDCs significantly affected the surface properties of all DBMs but at varying degrees. Corega produced the highest negative effect on roughness and color change while H 2 O 2 dramatically affected the microhardness. Prolonged use of CDCs should be cautiously followed.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Dental Biomaterials, Faculty of Dental Medicine, Al-Azhar University, Cairo, Egypt.
- Department of Prosthodontics, Faculty of Dental Medicine, Al-Azhar University, Cairo, Egypt.
- Al Mouwasat Hospital, Al Madinah Al Mounawarah, KSA.
- Department of Dental Biomaterials, Faculty of Dental Medicine, Al-Azhar University, Assuit, Egypt.
- Department of Substitutive Dental Sciences, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.
ORCID-Profile: Reem Abualsaud, Mohamed Ahmed Helal
Zitieren
APA
Elrahim, R. A. A., Shown, A., Abdellah, M., Abualsaud, R., & Helal, M. A. (2024). Impact of different chemical denture cleansers on the properties of digitally fabricated denture base resin materials. Journal of Prosthodontics, 33(7), 691-699. https://doi.org/10.1111/jopr.13761
Vancouver
Elrahim RAA, Shown A, Abdellah M, Abualsaud R, Helal MA. Impact of different chemical denture cleansers on the properties of digitally fabricated denture base resin materials. Journal of Prosthodontics. 2024;33(7):691-699. doi:10.1111/jopr.13761
BibTeX
@article{Elrahim2024,
author = {Elrahim, Ramy Abdallah Abd and Shown, Ahmed and Abdellah, Mahmoud and Abualsaud, Reem and Helal, Mohamed Ahmed},
title = {Impact of different chemical denture cleansers on the properties of digitally fabricated denture base resin materials},
journal = {Journal of Prosthodontics},
year = {2024},
volume = {33},
number = {7},
pages = {691--699},
doi = {10.1111/jopr.13761}
}
EUVIMED