EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access · CC BY 4.0

Comparative Analysis of the Mechanical and Biofilm Surface Formation of 3D Printed Resins and Milled PMMA Blocks With and Without Inorganic Fillers

Indyara Cerutti, Juliana S R de Andrade iD, Andressa da Silva Barboza iD, Jaqueline B Machado iD, Dewey Du-Hyeong Lee iD, Mateus Bertolini Fernandes Dos Santos iD

Clinical and Experimental Dental Research · 2026-08 · 12 (4)

DOI: 10.1002/cre2.70433 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift Clinical and Experimental Dental Research, online erschienen am 13.08.2026. Verfasst von Indyara Cerutti und 5 weiteren Autor:innen. Beteiligte Einrichtung: Graduate Program in Dentistry, Federal University of Pelotas, Pelotas, RS, Brazil. Hauptthemen laut MEDLINE: Polymethyl Methacrylate, Biofilms, Printing, Three-Dimensional, Composite Resins. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Coordination for the Improvement of HigherEducation Personnel (CAPES).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

Despite the growing number of studies assessing the performance of temporary restorative materials fabricated through CAD/CAM technologies, comparative analyses among 3D printed resins and milled PMMA blocks with differing compositions remain limited. This study compared mechanical and biofilm surface formation of 3D printed resins PMMA blocks with different compositions, using composite resin as control. Material and Methods Bar‑shaped (25 × 2 × 2 mm) and disc‑shaped (6 × 2 mm) specimens were fabricated. Flexural strength was evaluated by three‑point bending (ISO 4049), and Vickers microhardness was recorded. Multispecies biofilm formation was quantified using CFU/mL and examined morphologically via SEM. Statistical significance was set at α = 0.05.

Results

The 3D printed resins and milled hybrid PMMA showed the lowest flexural strength, with no significant differences between them, while the composite resin achieved the highest and statistically superior values ( p < 0.001). 3D printed resin without inorganic fillers showed the lowest Vickers microhardness values (12.66 ± 0.83 HK) while 3D printed resin with inorganic fillers (15.20 ± 1.94 HK) and milled conventional PMMA (16.03 ± 1.35 HK) exhibited higher values. However, none of them differed statistically from the 3D printed resin without inorganic fillers ( p = 0.064). Conversely, milled hybrid PMMA (16.67 ± 2.10 HK) demonstrated significantly higher Vickers microhardness than 3 d printed resin with inorganic fillers ( p < 0.001). Biofilm formation ranged from 2.26 × 10 7 to 2.82 × 10 7 CFU/mL, with no significant differences among materials ( p > 0.05).

Conclusions

Milled and 3D printed materials demonstrated comparable mechanical behavior while composite resin remained the performance benchmark. Material selection for provisional restorations should account for mechanical behavior and biological interactions, as surface treatment and clinical conditions may influence microbial colonization.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Polymethyl MethacrylateBiofilmsPrinting, Three-DimensionalComposite ResinsDental MaterialsMaterials TestingFlexural StrengthSurface PropertiesHardnessComputer-Aided Design

Stichwörter der Autor:innen

3D printingCAD/CAMPMMAbiofilm formationflexural strength

Substanzen

Polymethyl MethacrylateComposite ResinsDental Materials

Autor:innen und Institutionen

  • Graduate Program in Dentistry, Federal University of Pelotas, Pelotas, RS, Brazil.
  • Graduate Program in Dentistry, Federal University of Santa Catarina, Florianópolis, SC, Brazil.
  • Department of Prosthodontics, College of Dentistry and Dental Clinics, University of Iowa, Iowa City, Iowa, USA.

ORCID-Profile: Juliana S R de Andrade, Andressa da Silva Barboza, Jaqueline B Machado, Dewey Du-Hyeong Lee, Mateus Bertolini Fernandes Dos Santos

Förderung

  • Coordination for the Improvement of HigherEducation Personnel (CAPES)

Zitieren

APA

Cerutti, I., de Andrade, J. S. R., Barboza, A. D. S., Machado, J. B., Lee, D. D., & Dos Santos, M. B. F. (2026). Comparative Analysis of the Mechanical and Biofilm Surface Formation of 3D Printed Resins and Milled PMMA Blocks With and Without Inorganic Fillers. Clinical and Experimental Dental Research, 12(4). https://doi.org/10.1002/cre2.70433

Vancouver

Cerutti I, de Andrade JSR, Barboza ADS, Machado JB, Lee DD, Dos Santos MBF. Comparative Analysis of the Mechanical and Biofilm Surface Formation of 3D Printed Resins and Milled PMMA Blocks With and Without Inorganic Fillers. Clinical and Experimental Dental Research. 2026;12(4). doi:10.1002/cre2.70433

BibTeX
@article{Cerutti2026,
  author = {Cerutti, Indyara and de Andrade, Juliana S R and Barboza, Andressa da Silva and Machado, Jaqueline B and Lee, Dewey Du-Hyeong and Dos Santos, Mateus Bertolini Fernandes},
  title = {Comparative Analysis of the Mechanical and Biofilm Surface Formation of 3D Printed Resins and Milled PMMA Blocks With and Without Inorganic Fillers},
  journal = {Clinical and Experimental Dental Research},
  year = {2026},
  volume = {12},
  number = {4},
  doi = {10.1002/cre2.70433}
}
Kostenlos starten →