EUVIMEDEUVIMED entdecken
Crossref

In vitro assessment of polishing efficiency for additive-manufactured Co–Cr alloy clasps

Jyotetsu Takeyama, Toshitugu Sakurai, Hidemasa Shimpo, Noboru Kawamura, Chikahiro Ohkubo

Journal of Prosthodontic Research · 2024

DOI: 10.2186/jpr.jpr_d_23_00258 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontic Research, 2024. Verfasst von Jyotetsu Takeyama und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Oral Rehabilitation and Prosthodontics, Tsurumi University School of Dental Medicine, Yokohama, Japan. Hauptthemen laut MEDLINE: Chromium Alloys, Dental Polishing, Surface Properties. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 34 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

PURPOSE: The processes and methods of treating and polishing additive-manufactured (AMed) cobalt-chromium (Co-Cr) alloy clasps were assessed in vitro to determine their suitability for constant clinical use and the reduction of dental technician work. METHODS: AMed Aker clasps were fabricated by selective laser sintering of approximately 50 μm Co-Cr alloy powders. After the nodules and fins on the inner surface of the AMed clasps were removed and morphological correction was performed, a dental technician manually polished the clasps as a control. Four surface treatments, barrel finishing, shot peening, and wet and dry electropolishing, were performed to obtain smooth surfaces. In addition, hybrid manufacturing, which integrates repeated laser sintering and high-speed milling for one-process molding, was added to this study. After observing the treated surfaces using SEM and Hybrid Laser Microscope (HLM) the surface roughness, fitness accuracy, and retentive forces of the treated AMed clasps were measured, and their polishing efficiencies were compared. RESULTS: Similar to manual polishing, dry electropolishing yielded the smoothest surfaces in all treatments. The fitness accuracy of all clasp regions and treatment methods ranged from 80 to 140 μm, without significant differences among the treatment methods. All treated clasps showed acceptable retentive forces for clinical use, and hybrid manufacturing and wet electropolishing showed significantly higher forces. CONCLUSIONS: AMed Co-Cr clasps with all surface treatments could be clinically used if additional slight manual polishing was performed; however, each processing condition should be carefully selected.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Chromium AlloysDental PolishingSurface PropertiesDental ClaspsIn Vitro TechniquesMaterials TestingLasersHumansMicroscopy, Electron, Scanning

Stichwörter der Autor:innen

Additive manufacturingCo−Cr alloyFitness accuracyPolishing efficiencySurface roughness

Substanzen

Chromium Alloys

Autor:innen und Institutionen

  • Department of Oral Rehabilitation and Prosthodontics, Tsurumi University School of Dental Medicine, Yokohama, Japan.
  • Dental Technician Training Institute, Tsurumi University Dental Hospital, Yokohama, Japan.

Zitieren

APA

Takeyama, J., Sakurai, T., Shimpo, H., Kawamura, N., & Ohkubo, C. (2024). In vitro assessment of polishing efficiency for additive-manufactured Co–Cr alloy clasps. Journal of Prosthodontic Research. https://doi.org/10.2186/jpr.jpr_d_23_00258

Vancouver

Takeyama J, Sakurai T, Shimpo H, Kawamura N, Ohkubo C. In vitro assessment of polishing efficiency for additive-manufactured Co–Cr alloy clasps. Journal of Prosthodontic Research. 2024. doi:10.2186/jpr.jpr_d_23_00258

BibTeX
@article{Takeyama2024,
  author = {Takeyama, Jyotetsu and Sakurai, Toshitugu and Shimpo, Hidemasa and Kawamura, Noboru and Ohkubo, Chikahiro},
  title = {In vitro assessment of polishing efficiency for additive-manufactured Co–Cr alloy clasps},
  journal = {Journal of Prosthodontic Research},
  year = {2024},
  doi = {10.2186/jpr.jpr_d_23_00258}
}
Kostenlos starten →