EUVIMEDEUVIMED entdecken
Open Access · CC BY-ND 4.0

Marginal fit of milled versus different 3D-printed materials for provisional fixed dental prostheses: an in vitro comparative study

Anca Igreţ, Raul Nicolae Rotar, Codruţa Ille, Florin Topală, Anca Jivănescu

Medicine and Pharmacy Reports · 16.06.2023 · 96 (3) · 298-304

DOI: 10.15386/mpr-2588 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Medicine and Pharmacy Reports, online erschienen am 16.06.2023. Verfasst von Anca Igreţ und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Dentistry, Victor Babeş University of Medicine and Pharmacy, Timişoara, Romania. Die Arbeit wurde bisher 18-mal zitiert (Crossref). Der Volltext ist frei zugänglich (Open Access, CC BY-ND 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Introduction

Provisional dental prostheses are used as interim restorations to help patients perform oral functions between the time of tooth preparation and the placement of the final restoration. A provisional dental prosthesis should protect the abutment from pulpal and gingival aggressions, adapt correctly to keep healthy gingival tissues, be durable, and have a low price. The purpose of this in vitro study was to compare the marginal adaptation of different types of provisional fixed dental prostheses (PFDP), fabricated using 3D printing technology versus the milling (computer-aided manufacturing [CAM]) technique.

Method

Two resin teeth (second premolar and second molar) on a typodont were prepared for three-unit provisional fixed dental prostheses. Thirty models were 3D-printed after a digital model was created using an intraoral scanner. Then, 30 provisional fixed dental prostheses (PFDPs) were made from a variety of materials using a digital design of a 3-unit PFDP and STL files delivered to a milling machine and a 3D printer, respectively. Ten PFDP were milled (CAM), and two sets of ten each, were fabricated with 3D printing technology (stereolithography), using two different materials. All restorations were analyzed under a microscope, and marginal gap was then measured using the software Image J.

Results

The milled group presented the best marginal gap values (ranging from 86 to 108 μm) and a median value of 93 μm, followed by GC group with (110-251 μm) with a median value of 205 μm and the PR group with median value of 316.5 μm.

Conclusion

According to the findings of this in vitro study, the milling (CAM) technique and SLA technology provides acceptable marginal fit values to fabricate provisional fixed partial dentures.

Schlagwörter

Stichwörter der Autor:innen

3D printingCAD/CAMdigital dentistrymaterials

Autor:innen und Institutionen

  • Department of Prosthodontics, Faculty of Dentistry, Victor Babeş University of Medicine and Pharmacy, Timişoara, Romania.
  • TADERP Research Center, UMFVBT, Timişoara, Romania.

Zitieren

APA

Igreţ, A., Rotar, R. N., Ille, C., Topală, F., & Jivănescu, A. (2023). Marginal fit of milled versus different 3D-printed materials for provisional fixed dental prostheses: an in vitro comparative study. Medicine and Pharmacy Reports, 96(3), 298-304. https://doi.org/10.15386/mpr-2588

Vancouver

Igreţ A, Rotar RN, Ille C, Topală F, Jivănescu A. Marginal fit of milled versus different 3D-printed materials for provisional fixed dental prostheses: an in vitro comparative study. Medicine and Pharmacy Reports. 2023;96(3):298-304. doi:10.15386/mpr-2588

BibTeX
@article{Igre2023,
  author = {Igreţ, Anca and Rotar, Raul Nicolae and Ille, Codruţa and Topală, Florin and Jivănescu, Anca},
  title = {Marginal fit of milled versus different 3D-printed materials for provisional fixed dental prostheses: an in vitro comparative study},
  journal = {Medicine and Pharmacy Reports},
  year = {2023},
  volume = {96},
  number = {3},
  pages = {298--304},
  doi = {10.15386/mpr-2588}
}
Kostenlos starten →