EUVIMEDEUVIMED entdecken
Crossref

Wear resistance of 3D‐printed and milled denture teeth materials for complete‐arch implant‐supported prostheses: An in vitro study

Said Sanchez iD, Ghida Lawand iD, Adnan Bazarbashi, Camila Jreige iD, Jack Marrano, William Martin iD, Luiz Gonzaga iD, Mateus G Rocha iD

Journal of Prosthodontics · 07.07.2026

DOI: 10.1111/jopr.70184 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 07.07.2026. Verfasst von Said Sanchez und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics and Implantology, La Salle Bajío University, León, México. Die Arbeit nennt 46 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

The purpose of this in vitro study was to compare the two‐body wear resistance of milled and 3D‐printed denture teeth against various CAD‐CAM prosthetic materials. Materials and Methods A total of 112 specimens were fabricated from three materials: monolithic 4 mol% yttria‐stabilized tetragonal zirconia polycrystal (ArgenZ HT+ Zirconia), 3D‐milled highly cross‐linked polymethylmethacrylate denture teeth material (milled PMMA [mPMMA], Ivotion), and 3D‐printed resin denture teeth (3D‐PR, Flexcera Smile). Seven antagonist/sample groups (Z/Z (G1), Z/mPMMA (G2), Z/3D‐PR (G3), mPMMA/mPMMA (G4), 3D‐PR/3D‐PR (G5), mPMMA/3D‐PR (G6), and 3D‐PR/mPMMA (G7)) were tested to evaluate the factorial inter‐arch association between the three materials ( N = 16 per group; antagonist ( n = 8), sample ( n = 8)). Specimens underwent two‐body wear testing in a chewing simulator under thermocycling. Volumetric wear loss and vertical height loss were measured by laser scanning and analyzed by two‐way repeated‐measures ANOVA.

Results

All material pairings showed progressive, near‐linear volumetric wear with increasing cycles. Zirconia‐based groups exhibited significantly lower wear than polymeric combinations. Total height loss ranged from 0.266 mm (G1) to 1.007 mm (G6). When zirconia opposed polymers, wear was concentrated on the polymer surface (∼95%), whereas the 3D‐PR/mPMMA (G7) pairing was the only group where antagonist wear exceeded sample wear.

Conclusions

Material type and positioning significantly influenced wear behavior. Zirconia showed superior wear resistance, followed by mPMMA and 3D‐PR. Material positioning critically affected wear distribution, with implications for vertical dimension of occlusion maintenance in implant‐supported prostheses.

Schlagwörter

Stichwörter der Autor:innen

3D printingCAD‐CAMdental implantsdental prosthesispolymethylmethacrylatetooth wearzirconia

Autor:innen und Institutionen

  • Department of Prosthodontics and Implantology, La Salle Bajío University, León, México.
  • Department of Oral and Maxillofacial Surgery, Center for Implant Dentistry, University of Florida College of Dentistry, Gainesville, Florida, USA.
  • Department of Prosthodontics, King Saud University, Riyadh, Saudi Arabia.
  • Department of Prosthodontics, University of São Paulo School of Dentistry, São Paulo, Brazil.
  • Absolute Lab, Durham, North Carolina, USA.
  • Center for Dental Biomaterials, University of Florida College of Dentistry, Gainesville, Florida, USA.

ORCID-Profile: Said Sanchez, Ghida Lawand, Camila Jreige, William Martin, Luiz Gonzaga, Mateus G Rocha

Zitieren

APA

Sanchez, S., Lawand, G., Bazarbashi, A., Jreige, C., Marrano, J., Martin, W., Gonzaga, L., & Rocha, M. G. (2026). Wear resistance of 3D‐printed and milled denture teeth materials for complete‐arch implant‐supported prostheses: An in vitro study. Journal of Prosthodontics. https://doi.org/10.1111/jopr.70184

Vancouver

Sanchez S, Lawand G, Bazarbashi A, Jreige C, Marrano J, Martin W, et al. Wear resistance of 3D‐printed and milled denture teeth materials for complete‐arch implant‐supported prostheses: An in vitro study. Journal of Prosthodontics. 2026. doi:10.1111/jopr.70184

BibTeX
@article{Sanchez2026,
  author = {Sanchez, Said and Lawand, Ghida and Bazarbashi, Adnan and Jreige, Camila and Marrano, Jack and Martin, William and Gonzaga, Luiz and Rocha, Mateus G},
  title = {Wear resistance of 3D‐printed and milled denture teeth materials for complete‐arch implant‐supported prostheses: An in vitro study},
  journal = {Journal of Prosthodontics},
  year = {2026},
  doi = {10.1111/jopr.70184}
}
Kostenlos starten →