EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access · CC BY 4.0

Microstructure—Machinability correlation in heat treated AISI 1040 steel: Comparative analysis of tool life and surface roughness

Umanath R Poojary, Ananda Hegde iD, Sriharsha Hegde iD, Rayappa Shrinivas Mahale

PLOS One · 22.06.2026 · 21 (6) · e0352093

DOI: 10.1371/journal.pone.0352093 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift PLOS One, online erschienen am 22.06.2026. Verfasst von Umanath R Poojary und 3 weiteren Autor:innen. Beteiligte Einrichtung: Manipal Institute of Technology, Manipal Academy of Higher Education, Manipal, Karnataka, India. Hauptthemen laut MEDLINE: Steel, Hot Temperature. Die Arbeit nennt 14 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study presents an integrated investigation of the machinability of heat treated AISI 1040 steel under annealed, normalized, and oil quenched conditions. The effects of heat treatment parameters, namely austenitizing temperature and soaking time, together with machining parameters including cutting speed, feed rate, and depth of cut, were evaluated in terms of tool life and surface roughness. Experiments were designed using a Taguchi L27 orthogonal array, and the responses were analyzed through analysis of variance (ANOVA), regression modeling, and optimization techniques. The results showed that temperature, cutting speed, and feed rate significantly influenced tool life, whereas feed rate was the most dominant factor affecting surface roughness in all heat treatment conditions. Annealed AISI 1040 steel exhibited the highest tool life and the best overall machinability because of its relatively softer ferrite-pearlite microstructure, while oil quenched specimens showed the lowest tool life due to the formation of hard martensitic phases. Normalized specimens displayed intermediate behavior, indicating a balanced combination of strength and machinability. The developed regression models showed good predictive capability for both tool life and surface roughness within the investigated parameter range. SEM analysis further confirmed that the observed variations in machinability were closely associated with microstructural evolution caused by different heat treatment routes. The study provides useful guidance for selecting suitable heat treatment and machining parameters to improve productivity, tool performance, and surface quality during machining of AISI 1040 steel.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

SteelHot TemperatureSurface PropertiesMaterials TestingMicroscopy, Electron, Scanning

Substanzen

Steel

Autor:innen und Institutionen

  • Manipal Institute of Technology, Manipal Academy of Higher Education, Manipal, Karnataka, India.
  • Department of Automation and Robotics, JSPM's Rajarshi Shahu College of Engineering, Pune, Maharashtra, India.

ORCID-Profile: Ananda Hegde, Sriharsha Hegde

Zitieren

APA

Poojary, U. R., Hegde, A., Hegde, S., & Mahale, R. S. (2026). Microstructure—Machinability correlation in heat treated AISI 1040 steel: Comparative analysis of tool life and surface roughness. PLOS One, 21(6), e0352093. https://doi.org/10.1371/journal.pone.0352093

Vancouver

Poojary UR, Hegde A, Hegde S, Mahale RS. Microstructure—Machinability correlation in heat treated AISI 1040 steel: Comparative analysis of tool life and surface roughness. PLOS One. 2026;21(6):e0352093. doi:10.1371/journal.pone.0352093

BibTeX
@article{Poojary2026,
  author = {Poojary, Umanath R and Hegde, Ananda and Hegde, Sriharsha and Mahale, Rayappa Shrinivas},
  title = {Microstructure—Machinability correlation in heat treated AISI 1040 steel: Comparative analysis of tool life and surface roughness},
  journal = {PLOS One},
  year = {2026},
  volume = {21},
  number = {6},
  pages = {e0352093},
  doi = {10.1371/journal.pone.0352093}
}
Kostenlos starten →