Effect from the sequence of heat treatment and grinding on the mechanical properties of nickel–titanium rotary instruments
European Journal of Oral Sciences · 2026-06 · 134 (3)
DOI: 10.1111/eos.70074 ↗Kurz gefasst
Fachartikel in der Zeitschrift European Journal of Oral Sciences, online erschienen am 25.02.2026. Verfasst von Nayoung Bu und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Conservative Dentistry, School of Dentistry, Dental Research Institute, Dental and Life Science Institute, Pusan National University, Y…. Hauptthemen laut MEDLINE: Nickel, Titanium, Dental Alloys, Root Canal Preparation. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 29 Literaturangaben. Gefördert von: Pusan National University.
Abstract (Originalsprache)
This study aimed to evaluate how the sequence of heat treatment and grinding affects the mechanical properties of nickel–titanium rotary instruments. ProTaper Gold (PTG) and three experimental FQ files with identical designs, but different manufacturing sequences, were tested. FQhg was heat‐treated before grinding, FQgh was ground before heat treatment, and FQnh was not heat‐treated. Cyclic fatigue resistance, torsional resistance, and bending stiffness were measured ( n = 15). Scanning electron microscopy and differential scanning calorimetry (DSC) were performed. Statistical analysis was conducted using one‐way anova and Tukey's test at a 95% significance level. FQhg showed the highest cyclic fatigue resistance, followed by FQgh, FQnh, and PTG ( p < 0.05), while no significant differences were found in torsional strength, toughness, or distortion angle among the FQ groups. PTG showed higher torsional strength and bending stiffness, likely due to its different cross‐sectional design and taper. DSC analysis revealed minor differences in austenite transformation temperatures between FQhg and FQgh. The sequence of heat treatment and grinding significantly influenced cyclic fatigue resistance, with post‐heat‐treatment grinding (FQhg) providing superior performance; however, its impact on other mechanical properties was limited. The clinical relevance of processing sequence appears minimal compared to factors such as cross‐sectional design and heat treatment.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Conservative Dentistry, School of Dentistry, Dental Research Institute, Dental and Life Science Institute, Pusan National University, Yangsan, South Korea.
- Department of Conservative Dentistry, College of Dentistry, Kyungpook National University, Daegu, South Korea.
ORCID-Profile: Nayoung Bu, Jung-Hong Ha, Hyeon-Cheol Kim, Sang Won Kwak
Förderung
- Pusan National University
Zitieren
APA
Bu, N., Ha, J. H., Kim, H. C., & Kwak, S. W. (2026). Effect from the sequence of heat treatment and grinding on the mechanical properties of nickel–titanium rotary instruments. European Journal of Oral Sciences, 134(3). https://doi.org/10.1111/eos.70074
Vancouver
Bu N, Ha JH, Kim HC, Kwak SW. Effect from the sequence of heat treatment and grinding on the mechanical properties of nickel–titanium rotary instruments. European Journal of Oral Sciences. 2026;134(3). doi:10.1111/eos.70074
BibTeX
@article{Bu2026,
author = {Bu, Nayoung and Ha, Jung-Hong and Kim, Hyeon-Cheol and Kwak, Sang Won},
title = {Effect from the sequence of heat treatment and grinding on the mechanical properties of nickel–titanium rotary instruments},
journal = {European Journal of Oral Sciences},
year = {2026},
volume = {134},
number = {3},
doi = {10.1111/eos.70074}
}
EUVIMED