EUVIMEDScopri EUVIMED
Crossref

Laser-Induced Temperature Changes on the Outer Surface of Titanium Dental Implants: An In Vitro Study

Laurent Marchand, David Cornish, Philippe Mojon, Irena Sailer, Andreas Worni

The International Journal of Oral & Maxillofacial Implants · 2024

DOI: 10.11607/jomi.10656 ↗

At a glance

Journal article in The International Journal of Oral & Maxillofacial Implants, 2024. Written by Laurent Marchand and 4 co-authors. Major MEDLINE topics: Dental Implants, Titanium, Surface Properties, Lasers, Gas. Cited 1 times so far (Crossref).

AbstractSubjectsDati bibliograficiCiteRelated studies

Abstract (original language)

PURPOSE: To measure the surface temperature distribution after using a CO2 laser to heat titanium dental implants via different power settings, application intervals, and irradiation times. MATERIALS AND METHODS: A total of 10 tissue-level titanium implants (Screw-Line Promote Plus, Camlog; 4.3 × 11 mm) were placed (EpoFix, Struers) and irradiated with a CO2 laser (Denta 2, Lutronic) with a wavelength of 10.6 μm at power levels of 4 watts (Group 1), 6 watts (Group 2), 8 watts (Group 3), and 10 watts (Group 4). A continuous beam mode (setting I) and noncontinuous beam modes with 5-second (setting II) and 10-second (setting III) pause intervals were used. For each setting, a total irradiation time of 50 seconds was used and repeated 10 times. The temperature was measured using external thermocouple (Testo) in contact with the implant surface at the implant shoulder, middle, and apex. A linear regression model was used to analyze the data (P = .05). RESULTS: Setting I demonstrated the most rapid increase in implant surface temperature in all three test sites as well as the greatest total temperature at 50 seconds of irradiation time. The greater the pause interval (settings II and III) during the 50 seconds of irradiation, the lower the rate of temperature increase as well as the total temperature in all three test sites and with all power levels. The average temperature difference between the apex and shoulder site was significant for setting III for all groups, but not for any groups in settings I and II. CONCLUSIONS: Heating the internal aspect of an implant with a CO2 laser produces different temperature distribution profiles depending on the laser power level and the application interval. Laser-beam irradiation leads to a temperature gradient, which is greatest at the implant apex and smallest at the implant shoulder.

Subjects

MeSH terms (MEDLINE)

Dental ImplantsTitaniumSurface PropertiesLasers, GasIn Vitro TechniquesTemperatureHot TemperatureMaterials TestingHumans

Substances

Dental ImplantsTitanium

Cite

APA

Marchand, L., Cornish, D., Mojon, P., Sailer, I., & Worni, A. (2024). Laser-Induced Temperature Changes on the Outer Surface of Titanium Dental Implants: An In Vitro Study. The International Journal of Oral & Maxillofacial Implants. https://doi.org/10.11607/jomi.10656

Vancouver

Marchand L, Cornish D, Mojon P, Sailer I, Worni A. Laser-Induced Temperature Changes on the Outer Surface of Titanium Dental Implants: An In Vitro Study. The International Journal of Oral & Maxillofacial Implants. 2024. doi:10.11607/jomi.10656

BibTeX
@article{Marchand2024,
  author = {Marchand, Laurent and Cornish, David and Mojon, Philippe and Sailer, Irena and Worni, Andreas},
  title = {Laser-Induced Temperature Changes on the Outer Surface of Titanium Dental Implants: An In Vitro Study},
  journal = {The International Journal of Oral & Maxillofacial Implants},
  year = {2024},
  doi = {10.11607/jomi.10656}
}
Start for free →