EUVIMEDAtrasti EUVIMED
Crossref

Shear Bond Strength of Repair Materials by Different Polymerization Methods On 3D-Printed Denture Base

Yutaro Oyamada, Tomofumi Sawada, Atsuo Nakanishi, Hisatomo Kondo

The International Journal of Prosthodontics · 2025

DOI: 10.11607/ijp.9152 ↗

At a glance

Journal article in The International Journal of Prosthodontics, 2025. Written by Yutaro Oyamada and 3 co-authors. Major MEDLINE topics: Denture Bases, Polymethyl Methacrylate, Polymerization, Printing, Three-Dimensional.

SantraukaSubjectsBibliografiniai duomenysCiteRelated studies

Abstract (original language)

PURPOSE: To investigate shear bond strengths (SBSs) of denture repair materials using different polymerization methods to a 3D-printed denture base (DLP) compared to an autopolymerized polymethyl methacrylate denture base (PMMA). MATERIALS AND METHODS: DLP and PMMA disks were fabricated, roughened using #400 silicon carbide abrasive paper, and treated with the primer/bonding of the respective repair material. An autopolymerized denture repair material (PER) or a light-polymerized denture relining material (MRB) was polymerized on the disks. All specimens were stored in distilled water at 37°C for 24 hours. Half of the specimens underwent thermocycling (TC; 5,000 cycles, 5 to 55°C). SBS testing was conducted (n = 20 per group), and the fracture pattern was analyzed. The SBS data were analyzed using nonparametric Kruskal- Wallis tests and Weibull distributions with the maximum likelihood estimation. RESULTS: MRB specimens showed significantly higher SBS and Weibull characteristic strength values than PER specimens (P < .001), irrespective of the denture base material. No statistical differences were observed in Weibull modulus among the specimens, except PMMA-MRB specimens, which showed the highest values (P < .001). Thermal aging tended to decrease these values; however, no significant differences were observed between the non-TC and TC groups. Adhesive failure was dominantly observed in the specimens, except DLP-MRB specimens, which shifted to cohesive failures within the denture base. CONCLUSIONS: The repairability of the DLP specimens was comparable to those of the PMMA specimens. Thus, denture repair of the DLP denture base could be treated in the same manner as a conventional PMMA denture base.

Subjects

MeSH terms (MEDLINE)

Denture BasesPolymethyl MethacrylatePolymerizationPrinting, Three-DimensionalShear StrengthDental BondingDenture RepairDental MaterialsMaterials TestingDental Stress Analysis

Substances

Polymethyl MethacrylateDental Materials

Cite

APA

Oyamada, Y., Sawada, T., Nakanishi, A., & Kondo, H. (2025). Shear Bond Strength of Repair Materials by Different Polymerization Methods On 3D-Printed Denture Base. The International Journal of Prosthodontics. https://doi.org/10.11607/ijp.9152

Vancouver

Oyamada Y, Sawada T, Nakanishi A, Kondo H. Shear Bond Strength of Repair Materials by Different Polymerization Methods On 3D-Printed Denture Base. The International Journal of Prosthodontics. 2025. doi:10.11607/ijp.9152

BibTeX
@article{Oyamada2025,
  author = {Oyamada, Yutaro and Sawada, Tomofumi and Nakanishi, Atsuo and Kondo, Hisatomo},
  title = {Shear Bond Strength of Repair Materials by Different Polymerization Methods On 3D-Printed Denture Base},
  journal = {The International Journal of Prosthodontics},
  year = {2025},
  doi = {10.11607/ijp.9152}
}
Start for free →