EUVIMEDEUVIMED entdecken
Crossref

Shear bond strength of ultraviolet-polymerized resin to 3D-printed denture materials: Effects of post-polymerization, surface treatments, and thermocycling

Ami Tanaka, Tomohiro Kawaguchi, Ayaka Ito, Kota Isshi, Ippei Hamanaka, Takashi Tsuzuki

Journal of Prosthodontic Research · 2024 · 69 (1) · 21-29

DOI: 10.2186/jpr.jpr_d_23_00321 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontic Research, 2024. Verfasst von Ami Tanaka und 5 weiteren Autor:innen. Beteiligte Einrichtung: Division of Removable Prosthodontics, Department of Oral Rehabilitation, Fukuoka Dental College, Fukuoka, Japan. Hauptthemen laut MEDLINE: Shear Strength, Printing, Three-Dimensional, Ultraviolet Rays, Dental Bonding. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 47 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

PURPOSE: The purpose of this study is to compare the shear bond strength of ultraviolet (UV)-polymerized resin to 3D-printed denture materials, both with and without post-polymerization. Moreover, the effects of surface treatment and thermocycling on shear bond strength after post-polymerization were investigated. METHODS: Cylindrical 3D-printed denture bases and teeth specimens were prepared. The specimens are subjected to two tests. For Test 1, the specimens were bonded without any surface treatment or thermal stress for comparison with and without post-polymerization. In Test 2, specimens underwent five surface treatments: untreated (CON), ethyl acetate (EA), airborne particle abrasion (APA) with 50 μm (50-APA) and 110 μm alumina (110-APA), and tribochemical silica coating (TSC). A UV-polymerized resin was used for bonding. Half of the Test 2 specimens were thermocycled for 10,000 cycles. Shear bond strength was measured and analyzed using Kruskal-Wallis and Steel-Dwass tests (n = 8). RESULTS: In Test 1, post-polymerization significantly reduced shear bond strength of both 3D-printed denture materials (P 0.05). In Test 2, before thermocycling, the CON and EA groups exhibited low bond strengths, while the 50-APA, 110-APA, and TSC groups exhibited higher bond strengths. Thermocycling did not reduce bond strength in the latter groups, but significantly reduced bond strength in the EA group (P < 0.001). CONCLUSIONS: Post-polymerization can significantly reduce the shear bond strength of 3D-printed denture materials. Surface treatments, particularly APA and TSC, maintained bond strength even after thermocycling.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Shear StrengthPrinting, Three-DimensionalUltraviolet RaysDental BondingPolymerizationDental MaterialsDenture BasesSurface PropertiesMaterials TestingTemperatureHumans

Stichwörter der Autor:innen

3D printingCAD-CAMbond strengthdenture basedigital denture

Substanzen

Dental Materials

Autor:innen und Institutionen

  • Division of Removable Prosthodontics, Department of Oral Rehabilitation, Fukuoka Dental College, Fukuoka, Japan.
  • Department of Biomaterials Science and Turku Clinical Biomaterials Centre - TCBC, Institute of Dentistry, University of Turku, Turku, Finland.
  • Central Dental Laboratory, Fukuoka Dental College Medical & Dental Hospital, Fukuoka, Japan.

Zitieren

APA

Tanaka, A., Kawaguchi, T., Ito, A., Isshi, K., Hamanaka, I., & Tsuzuki, T. (2024). Shear bond strength of ultraviolet-polymerized resin to 3D-printed denture materials: Effects of post-polymerization, surface treatments, and thermocycling. Journal of Prosthodontic Research, 69(1), 21-29. https://doi.org/10.2186/jpr.jpr_d_23_00321

Vancouver

Tanaka A, Kawaguchi T, Ito A, Isshi K, Hamanaka I, Tsuzuki T. Shear bond strength of ultraviolet-polymerized resin to 3D-printed denture materials: Effects of post-polymerization, surface treatments, and thermocycling. Journal of Prosthodontic Research. 2024;69(1):21-29. doi:10.2186/jpr.jpr_d_23_00321

BibTeX
@article{Tanaka2024,
  author = {Tanaka, Ami and Kawaguchi, Tomohiro and Ito, Ayaka and Isshi, Kota and Hamanaka, Ippei and Tsuzuki, Takashi},
  title = {Shear bond strength of ultraviolet-polymerized resin to 3D-printed denture materials: Effects of post-polymerization, surface treatments, and thermocycling},
  journal = {Journal of Prosthodontic Research},
  year = {2024},
  volume = {69},
  number = {1},
  pages = {21--29},
  doi = {10.2186/jpr.jpr_d_23_00321}
}
Kostenlos starten →