EUVIMEDAtrasti EUVIMED
Vergleichsstudie

Influence of Different Build Directions on the Fracture Load and Surface Roughness of Additively Manufactured Three-unit Provisional Restoration and Comparison with Conventional Methods of Provisional Fabrication

Shubhi Sahni, Pragati Kaurani, Shweta Bhambhu, Anuja Yadav

The International Journal of Prosthodontics · 2024

DOI: 10.11607/ijp.8813 ↗

At a glance

Vergleichsstudie in The International Journal of Prosthodontics, 2024. Written by Shubhi Sahni and 3 co-authors. Major MEDLINE topics: Dental Restoration, Temporary. Cited 1 times so far (Crossref).

SantraukaSubjectsBibliografiniai duomenysCiteRelated studies

Abstract (original language)

PURPOSE: To compare the influence of 0-, 45-, and 90-degree build directions on the fracture load and surface roughness of additively manufactured three-unit fixed provisional restorations and to compare the additively manufactured provisionals to provisionals fabricated using conventional methods. MATERIALS AND METHODS: Mandibular typodont right second molars and premolars were prepared for a missing mandibular first molar to receive a three-unit fixed partial denture. For six groups of 10 samples each, three-unit provisionals were fabricated using additive manufacturing at 0, 45, and 90 degrees; heat polymerized PMMA; autopolymerizing resin; and bis-acryl composites resins-and tested for fracture load and surface roughness. One-way ANOVA and Tukey tests were used to analyze the data. RESULTS: For fracture load, the lowest mean value was for autopolymerizing bis-acryl resin (464.9 N), and the highest value was for additive manufacturing at 0 degrees (596 N). Surface roughness values were lowest for heat-polymerized PMMA (0.132 µm), and the highest value was for autopolymerizing PMMA (0.836 µm). Significant differences were found between the three build directions for fracture load and surface roughness (P = .001); in all pairwise comparisons except between 0 and 90 degrees (P = .502) for fracture load; and between all three build directions for surface roughness (P = .01). Compared to other provisional materials, a significant difference (P = .001) was observed between all groups. CONCLUSIONS: Build direction affected the mechanical properties of additively manufactured three-unit provisionals, with provisionals printed at 0 degrees showing the highest fracture load and lowest surface roughness. Compared to other provisional materials, additively manufactured three-unit provisionals printed at 0 degrees also showed the highest fracture load, with surface roughness similar to heat-polymerized provisionals.

Subjects

MeSH terms (MEDLINE)

Dental Restoration, TemporarySurface PropertiesHumansIn Vitro TechniquesPolymethyl MethacrylateComposite ResinsDental Stress AnalysisMaterials TestingDental Restoration FailureDental Materials

Substances

Polymethyl MethacrylateComposite ResinsDental Materials

Cite

APA

Sahni, S., Kaurani, P., Bhambhu, S., & Yadav, A. (2024). Influence of Different Build Directions on the Fracture Load and Surface Roughness of Additively Manufactured Three-unit Provisional Restoration and Comparison with Conventional Methods of Provisional Fabrication. The International Journal of Prosthodontics. https://doi.org/10.11607/ijp.8813

Vancouver

Sahni S, Kaurani P, Bhambhu S, Yadav A. Influence of Different Build Directions on the Fracture Load and Surface Roughness of Additively Manufactured Three-unit Provisional Restoration and Comparison with Conventional Methods of Provisional Fabrication. The International Journal of Prosthodontics. 2024. doi:10.11607/ijp.8813

BibTeX
@article{Sahni2024,
  author = {Sahni, Shubhi and Kaurani, Pragati and Bhambhu, Shweta and Yadav, Anuja},
  title = {Influence of Different Build Directions on the Fracture Load and Surface Roughness of Additively Manufactured Three-unit Provisional Restoration and Comparison with Conventional Methods of Provisional Fabrication},
  journal = {The International Journal of Prosthodontics},
  year = {2024},
  doi = {10.11607/ijp.8813}
}
Start for free →