EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Impacts of Sterilization Method On Material Properties Of 3D Printable Resins With Prolonged Exposure To Cell Culture Environments

Ashlee S Liao iD, Michael J Bennington iD, Kevin Dai iD, Alaeddin Burak Irez iD, Anika Sun iD, Saul Schaffer iD, Bhavya Chopra iD, Ji Min Seok iD, Rebekah Adams iD, Yongjie Jessica Zhang iD, Victoria A Webster-Wood iD

Journal of Biomechanical Engineering · 2026

DOI: 10.1115/1.4071099 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Biomechanical Engineering, 2026. Verfasst von Ashlee S Liao und 10 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh, PA 15213. Hauptthemen laut MEDLINE: Sterilization, Printing, Three-Dimensional, Cell Culture Techniques, Resins, Synthetic. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Army Research Office, National Science Foundation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Low-cost 3D printing has become increasingly important in biomedical research, enabling rapid fabrication of custom cell culture devices, fixtures, and biohybrid robotic components. However, little is known about how common sterilization procedures and prolonged cell culture exposure impact the mechanical properties of commercially available resins. In this study, we analyzed five candidate 3D-printable resins-three rigid (Asiga DentaGUIDE, Liqcreate Bio-Med Clear, Phrozen AquaGray 8K) and two elastomeric (Asiga DentaGUM, Formlabs Silicone 40A)-to evaluate the effects of ethanol/UV and autoclave sterilization on material properties in phosphate-buffered saline (PBS) at physiological conditions. Using stress-strain data from tensile and compressive mechanical tests, elastic moduli, ultimate tensile strength, and strain at break were compared across sterilization techniques. Results showed that sterilization significantly altered the mechanical properties of rigid resins, with Phrozen AquaGray 8K and Liqcreate Bio-Med Clear exhibiting large reductions in tensile stiffness and strength, while Asiga DentaGUIDE retained greater stability. In contrast, elastomeric resins were more robust: Asiga DentaGUM and Formlabs Silicone 40A demonstrated minimal or non-significant changes across sterilization methods, though post-treatment protocols influenced variability. Notably, several rigid resins also exhibited substantially lower moduli in PBS compared to manufacturer-reported values. These findings emphasize the need for experimental validation of 3D printed resin properties under intended use conditions and suggest that Asiga DentaGUIDE and Formlabs Silicone 40A are promising candidates for biohybrid applications. Overall, this work provides critical guidance for selecting sterilization-compatible materials for biomedical devices and biohybrid robotics.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

SterilizationPrinting, Three-DimensionalCell Culture TechniquesResins, SyntheticMechanical PhenomenaMaterials TestingTensile StrengthStress, MechanicalElastic ModulusTime FactorsCompressive Strength

Substanzen

Resins, Synthetic

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh, PA 15213.
  • Johns Hopkins University Applied Physics Laboratory.
  • Carnegie Mellon University.
  • Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh, PA 15213; Department of Biomedical Engineering, Carnegie Mellon University, Pittsburgh, PA 15213; Department of Mechanical Engineering, Istan…
  • Istanbul Technical University.
  • Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh, PA 15213; Department of Biomedical Engineering, Carnegie Mellon University, Pittsburgh, PA 15213.

ORCID-Profile: Ashlee S Liao, Michael J Bennington, Kevin Dai, Alaeddin Burak Irez, Anika Sun, Saul Schaffer, Bhavya Chopra, Ji Min Seok, Rebekah Adams, Yongjie Jessica Zhang, Victoria A Webster-Wood

Förderung

  • Army Research Office
  • National Science Foundation

Zitieren

APA

Liao, A. S., Bennington, M. J., Dai, K., Irez, A. B., Sun, A., Schaffer, S., Chopra, B., Seok, J. M., Adams, R., Zhang, Y. J., & Webster-Wood, V. A. (2026). Impacts of Sterilization Method On Material Properties Of 3D Printable Resins With Prolonged Exposure To Cell Culture Environments. Journal of Biomechanical Engineering. https://doi.org/10.1115/1.4071099

Vancouver

Liao AS, Bennington MJ, Dai K, Irez AB, Sun A, Schaffer S, et al. Impacts of Sterilization Method On Material Properties Of 3D Printable Resins With Prolonged Exposure To Cell Culture Environments. Journal of Biomechanical Engineering. 2026. doi:10.1115/1.4071099

BibTeX
@article{Liao2026,
  author = {Liao, Ashlee S and Bennington, Michael J and Dai, Kevin and Irez, Alaeddin Burak and Sun, Anika and Schaffer, Saul and Chopra, Bhavya and Seok, Ji Min and Adams, Rebekah and Zhang, Yongjie Jessica and Webster-Wood, Victoria A},
  title = {Impacts of Sterilization Method On Material Properties Of 3D Printable Resins With Prolonged Exposure To Cell Culture Environments},
  journal = {Journal of Biomechanical Engineering},
  year = {2026},
  doi = {10.1115/1.4071099}
}
Kostenlos starten →