EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access · CC BY 4.0

Post‐curing effects on mechanical properties staining resistance of a 3D‐printed resin versus a direct composite for definitive restorations

Bianca Rossi iD, Arthur Henrique Marques Massarenti iD, Giulia Gamero Pizzanelli iD, Márcia Valéria Gualberto Barbosa de Queiroz iD, Filipe Milazzo Dos Santos iD, Matheus Kury iD, Adriano Fonseca Lima iD

European Journal of Oral Sciences · 2026

DOI: 10.1111/eos.70093 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift European Journal of Oral Sciences, 2026. Verfasst von Bianca Rossi und 6 weiteren Autor:innen. Beteiligte Einrichtung: Dental Research Division, Paulista University, Sao Paulo, Brazil. Hauptthemen laut MEDLINE: Composite Resins, Printing, Three-Dimensional, Dental Restoration, Permanent, Dental Materials. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Coordenação de Aperfeiçoamento de Pessoal de Nível Superior, Brasil (CAPES).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study evaluated the mechanical performance and staining resistance of a three‐dimensional (3D)‐printed resin (VarseoSmile Crown Plus) subjected to different post‐curing times (0, 5, 10, 15, and 20 min), compared with a conventional nanofilled resin composite (Filtek Z350XT). Specimens of both materials were fabricated and tested for flexural strength and flexural modulus using a three‐point bending test, whereas cohesive strength (CS) was assessed by microtensile testing. For color analysis, disk specimens were immersed in artificial saliva, Coca‐Cola, or red wine (RW) for 7 days, followed by polishing and whitening procedures. Color change (Δ E 00 ) and whiteness index (ΔWI D ) were recorded. Data were analyzed using a generalized linear model and Bonferroni tests ( α = 5%). The direct composite showed higher flexural and CS than the 3D‐printed resin. Post‐curing improved the mechanical properties of the printed material, although values remained inferior to those of the composite. Both materials exhibited color changes after staining, with RW causing the greatest discoloration. Polishing and whitening reduced staining but did not always restore baseline values. Although post‐curing enhances 3D‐printed resin performance, its mechanical behavior and color stability remain inferior to those of conventional composites, indicating the need for further optimization before clinical use as definitive restorations.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Composite ResinsPrinting, Three-DimensionalDental Restoration, PermanentDental MaterialsFlexural StrengthMaterials TestingTensile StrengthColorHumansDental Stress AnalysisTime FactorsSaliva, ArtificialElastic Modulus

Stichwörter der Autor:innen

cohesiveelastic modulusflexural strengthpolymer

Substanzen

Composite Resinsfiltek Z350Dental MaterialsSaliva, Artificial

Autor:innen und Institutionen

  • Dental Research Division, Paulista University, Sao Paulo, Brazil.

ORCID-Profile: Bianca Rossi, Arthur Henrique Marques Massarenti, Giulia Gamero Pizzanelli, Márcia Valéria Gualberto Barbosa de Queiroz, Filipe Milazzo Dos Santos, Matheus Kury, Adriano Fonseca Lima

Förderung

  • Coordenação de Aperfeiçoamento de Pessoal de Nível Superior
  • Brasil (CAPES)

Zitieren

APA

Rossi, B., Massarenti, A. H. M., Pizzanelli, G. G., Queiroz, M. V. G. B., Santos, F. M. D., Kury, M., & Lima, A. F. (2026). Post‐curing effects on mechanical properties staining resistance of a 3D‐printed resin versus a direct composite for definitive restorations. European Journal of Oral Sciences. https://doi.org/10.1111/eos.70093

Vancouver

Rossi B, Massarenti AHM, Pizzanelli GG, Queiroz MVGB, Santos FMD, Kury M, et al. Post‐curing effects on mechanical properties staining resistance of a 3D‐printed resin versus a direct composite for definitive restorations. European Journal of Oral Sciences. 2026. doi:10.1111/eos.70093

BibTeX
@article{Rossi2026,
  author = {Rossi, Bianca and Massarenti, Arthur Henrique Marques and Pizzanelli, Giulia Gamero and Queiroz, Márcia Valéria Gualberto Barbosa de and Santos, Filipe Milazzo Dos and Kury, Matheus and Lima, Adriano Fonseca},
  title = {Post‐curing effects on mechanical properties staining resistance of a 3D‐printed resin versus a direct composite for definitive restorations},
  journal = {European Journal of Oral Sciences},
  year = {2026},
  doi = {10.1111/eos.70093}
}
Kostenlos starten →