EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Effect of changing the internal structure on the mechanical properties of three‐dimensional‐printed custom tray material: An in vitro study

Cafer Anıl Erdem iD, Selin Çelik Öge iD, Orhun Ekren iD

European Journal of Oral Sciences · 2025

DOI: 10.1111/eos.13033 ↗

Kurz gefasst

Fachartikel in der Zeitschrift European Journal of Oral Sciences, 2025. Verfasst von Cafer Anıl Erdem und 2 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Dentistry, Department of Prosthodontics, Çukurova University, Adana, Turkey. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Dental Impression Materials. Die Arbeit nennt 14 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Cukurova University Scientific Research Project Coordination Unit.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The main challenges to the widespread clinical application of three‐dimensional (3D)‐printed customized trays include cost and time limitations. This study examined how changing the internal structure of 3D‐printed materials used for customized trays affects flexural strength (FS), flexural modulus (FM), manufacturing time, and material weight. Specimens (64 × 10 × 3.3 mm) were printed using a light‐sensitive liquid resin. The internal structures of control specimens were completely filled, whereas the internal structures of test groups comprised vertical bars spaced 1 mm (Test 1) or 2 mm (Test 2) apart. Specimens were weighed and then subjected to a three‐point bending test to evaluate their FS and FM. Data were analyzed using one‐way ANOVA and Tukey's test, with Weibull analysis applied to FS values. Control specimens had the highest FS (106 ± 4 MPa), while Test 2 specimens demonstrated the highest FM (6101 ± 1407 MPa). No significant differences were found between Test 1 and Test 2 specimens in FS or FM. Test 2 specimens had the lowest mean weight (1440 ± 42 mg). Manufacturing times were 80 min for control and Test 1 specimens and 60 min for Test 2 specimens. Including spaces in the internal structure of 3D‐printed custom tray material saves material and manufacturing time while maintaining mechanical properties.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalDental Impression MaterialsMaterials TestingFlexural StrengthElastic ModulusHumansTime FactorsDental Stress AnalysisIn Vitro TechniquesStress, Mechanical

Stichwörter der Autor:innen

dental impression techniqueflexural modulusflexural strengththree‐dimensional printing

Substanzen

Dental Impression Materials

Autor:innen und Institutionen

  • Faculty of Dentistry, Department of Prosthodontics, Çukurova University, Adana, Turkey.

ORCID-Profile: Cafer Anıl Erdem, Selin Çelik Öge, Orhun Ekren

Förderung

  • Cukurova University Scientific Research Project Coordination Unit

Zitieren

APA

Erdem, C. A., Çelik Öge, S., & Ekren, O. (2025). Effect of changing the internal structure on the mechanical properties of three‐dimensional‐printed custom tray material: An in vitro study. European Journal of Oral Sciences. https://doi.org/10.1111/eos.13033

Vancouver

Erdem CA, Çelik Öge S, Ekren O. Effect of changing the internal structure on the mechanical properties of three‐dimensional‐printed custom tray material: An in vitro study. European Journal of Oral Sciences. 2025. doi:10.1111/eos.13033

BibTeX
@article{Erdem2025,
  author = {Erdem, Cafer Anıl and Çelik Öge, Selin and Ekren, Orhun},
  title = {Effect of changing the internal structure on the mechanical properties of three‐dimensional‐printed custom tray material: An in vitro study},
  journal = {European Journal of Oral Sciences},
  year = {2025},
  doi = {10.1111/eos.13033}
}
Kostenlos starten →