EUVIMEDEUVIMED entdecken
Crossref

Wear and Fracture Resistance of 3D‐Printed Denture Teeth: An In Vitro Comparative Study

Mohammed M Gad iD, Rahaf Alghamdi iD, Raghad Al-Ghamdi iD, Alaa Al-Jefri iD, Sultan Akhtar iD, Soban Qadir Khan iD, Haidar Alalawi iD, Faisal D Al-Qarni iD

Journal of Prosthodontics · 2023-02 · 32 (2) · 170-177

DOI: 10.1111/jopr.13521 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 27.04.2022. Verfasst von Mohammed M Gad und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Substitutive Dental Sciences, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia. Hauptthemen laut MEDLINE: Quality of Life, Acrylic Resins. Die Arbeit wurde bisher 25-mal zitiert (Crossref) und nennt 30 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

The longevity of removable prostheses is mostly influenced by the properties of the used materials. The ability of the material to withstand high occlusal loads without deformation can enhance patient satisfaction and quality of life. This in vitro study aimed to investigate the wear and fracture resistance of three‐dimensional (3D)‐printed teeth compared with commercially available acrylic resin teeth. Materials and methods A total of 40 prefabricated acrylic teeth and 40 3D‐printed teeth were prepared in two forms: anatomical for fracture resistance or flat for wear resistance (n = 10). For wear evaluation, specimens were scanned at baseline and then subjected to thermal cycling (10,000 cycles). This was followed by a chewing simulator (60,000 cycles) against either metal or natural tooth. Then, the specimens were scanned again. Wear analysis was performed by superimposing the standard tessellation language (STL) files from baseline and the final scans with the aid of GOM Inspect 2020 software. Fracture resistance was assessed with a universal testing machine at a crosshead speed of 0.5 mm/min before and after thermal cycling. Data were analyzed with two‐independent t‐test and two‐way ANOVA (α = 0.05).

Results

The 3D‐printed teeth showed significantly lower wear resistance than the prefabricated ones with both antagonists (metal, p = 0.049; natural tooth, p = 0.021). The fracture resistance of the 3D‐printed teeth was significantly higher than that of the prefabricated teeth before thermocycling ( p = 0.042). After thermal cycling, the fracture resistance of both groups was decreased with no significant differences between them ( p = 0.266).

Conclusions

The 3D‐printed teeth showed lower wear resistance and higher fracture resistance than the prefabricated ones. Thermal cycling negatively affected the fracture resistance of 3D‐printed teeth.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Quality of LifeAcrylic ResinsHumansMaterials TestingDenturesPrinting, Three-Dimensional

Stichwörter der Autor:innen

3D printingdenture teethocclusal wearremovable dental prosthesis

Substanzen

Acrylic Resins

Autor:innen und Institutionen

  • Department of Substitutive Dental Sciences, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.
  • College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.
  • Department of Biophysics, Institute for Research and Medical Consultations (IRMC), Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.
  • Department of Dental Education, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.

ORCID-Profile: Mohammed M Gad, Rahaf Alghamdi, Raghad Al-Ghamdi, Alaa Al-Jefri, Sultan Akhtar, Soban Qadir Khan, Haidar Alalawi, Faisal D Al-Qarni

Zitieren

APA

Gad, M. M., Alghamdi, R., Al-Ghamdi, R., Al-Jefri, A., Akhtar, S., Khan, S. Q., Alalawi, H., & Al-Qarni, F. D. (2023). Wear and Fracture Resistance of 3D‐Printed Denture Teeth: An In Vitro Comparative Study. Journal of Prosthodontics, 32(2), 170-177. https://doi.org/10.1111/jopr.13521

Vancouver

Gad MM, Alghamdi R, Al-Ghamdi R, Al-Jefri A, Akhtar S, Khan SQ, et al. Wear and Fracture Resistance of 3D‐Printed Denture Teeth: An In Vitro Comparative Study. Journal of Prosthodontics. 2023;32(2):170-177. doi:10.1111/jopr.13521

BibTeX
@article{Gad2023,
  author = {Gad, Mohammed M and Alghamdi, Rahaf and Al-Ghamdi, Raghad and Al-Jefri, Alaa and Akhtar, Sultan and Khan, Soban Qadir and Alalawi, Haidar and Al-Qarni, Faisal D},
  title = {Wear and Fracture Resistance of 3D‐Printed Denture Teeth: An In Vitro Comparative Study},
  journal = {Journal of Prosthodontics},
  year = {2023},
  volume = {32},
  number = {2},
  pages = {170--177},
  doi = {10.1111/jopr.13521}
}
Kostenlos starten →