EUVIMEDEUVIMED entdecken
Crossref

In vitro effect of simulated brushing on color stability, surface roughness, and microbial adhesion of characterizing resin composites for 3D‐printed denture bases

Pamela Tayná Matias Bezerra, Lucas Cavalcante de Sousa, Ana Larisse Carneiro Pereira iD, Ana Luísa Cassiano Alves Bezerra, Maria Heloisa de Souza Borges Grisi iD, Leopoldina de Fátima Dantas de Almeida, André Ulisses Dantas Batista iD, Gabriela Queiroz de Melo Monteiro iD, Adriana da Fonte Porto Carreiro iD

Journal of Prosthodontics · 10.10.2025

DOI: 10.1111/jopr.70040 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 10.10.2025. Verfasst von Pamela Tayná Matias Bezerra und 8 weiteren Autor:innen. Beteiligte Einrichtung: Department of Dentistry, Federal University of Rio Grande do Norte (UFRN), Natal, Rio Grande do Norte, Brazil. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 33 Literaturangaben. Gefördert von: Coordenação de Aperfeiçoamento de Pessoal de Nível Superior.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

This in vitro study evaluated the effect of simulated brushing on color stability, surface roughness, and microbial adhesion of resin composites with different viscosities applied to denture base materials. Materials and Methods Disc‐shaped specimens (10 × 3.0 mm) were fabricated using a 3D‐printed denture base resin and heat‐polymerized resin. Three extrinsic characterizations (2 mm thick) were applied to the 3D‐printed resin specimens: one regular‐viscosity (RV) and two low‐viscosity (LV49, LV30), and light‐cured. The heat‐polymerized resin group (STG) was fabricated and characterized using a compression‐molding technique. Color coordinates and color stability (Δ E 00 ) were measured using a colorimeter; surface roughness ( R a ) was assessed using an optical profilometer; and microbial adhesion ( Candida albicans , log CFU/mL) was evaluated before and after 20,000 brushing cycles. Color and roughness data were analyzed using the Kruskal–Wallis test and the Wilcoxon signed‐rank test, while microbial adhesion was analyzed using one‐way ANOVA followed by Tukey's post hoc test ( α = 0.05).

Results

STG and LV49 exhibited greater color changes than did LV30 ( p < 0.05), but all groups remained within clinically acceptable limits (Δ E 00 ≤ 2.25). Brushing increased surface roughness in all groups except STG ( p < 0.05). Microbial adhesion increased after simulated brushing ( p < 0.05); however, no significant differences were observed between the groups ( p > 0.05).

Conclusions

Simulated brushing affected color stability, with some groups exhibiting clinically noticeable changes. It increased surface roughness in characterizing resin composites and enhanced Candida albicans adhesion in all groups, with no significant differences between materials.

Schlagwörter

Stichwörter der Autor:innen

3D printingdenture base resingingival composite

Autor:innen und Institutionen

  • Department of Dentistry, Federal University of Rio Grande do Norte (UFRN), Natal, Rio Grande do Norte, Brazil.
  • Postgraduate Program in Dentistry (PPGO), Federal University of Paraíba (UFPB), João Pessoa, Paraíba, Brazil.
  • Dental School, University of Pernambuco (UPE), Recife, Pernambuco, Brazil.
  • Department of Restorative Dentistry, Federal University of Paraíba (UFPB), João Pessoa, Paraíba, Brazil.

ORCID-Profile: Ana Larisse Carneiro Pereira, Maria Heloisa de Souza Borges Grisi, André Ulisses Dantas Batista, Gabriela Queiroz de Melo Monteiro, Adriana da Fonte Porto Carreiro

Förderung

  • Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Zitieren

APA

Bezerra, P. T. M., de Sousa, L. C., Pereira, A. L. C., Bezerra, A. L. C. A., de Souza Borges Grisi, M. H., de Fátima Dantas de Almeida, L., Batista, A. U. D., de Melo Monteiro, G. Q., & da Fonte Porto Carreiro, A. (2025). In vitro effect of simulated brushing on color stability, surface roughness, and microbial adhesion of characterizing resin composites for 3D‐printed denture bases. Journal of Prosthodontics. https://doi.org/10.1111/jopr.70040

Vancouver

Bezerra PTM, de Sousa LC, Pereira ALC, Bezerra ALCA, de Souza Borges Grisi MH, de Fátima Dantas de Almeida L, et al. In vitro effect of simulated brushing on color stability, surface roughness, and microbial adhesion of characterizing resin composites for 3D‐printed denture bases. Journal of Prosthodontics. 2025. doi:10.1111/jopr.70040

BibTeX
@article{Bezerra2025,
  author = {Bezerra, Pamela Tayná Matias and de Sousa, Lucas Cavalcante and Pereira, Ana Larisse Carneiro and Bezerra, Ana Luísa Cassiano Alves and de Souza Borges Grisi, Maria Heloisa and de Fátima Dantas de Almeida, Leopoldina and Batista, André Ulisses Dantas and de Melo Monteiro, Gabriela Queiroz and da Fonte Porto Carreiro, Adriana},
  title = {In vitro effect of simulated brushing on color stability, surface roughness, and microbial adhesion of characterizing resin composites for 3D‐printed denture bases},
  journal = {Journal of Prosthodontics},
  year = {2025},
  doi = {10.1111/jopr.70040}
}
Kostenlos starten →