EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Surface Changes Induced by Brushing Increase Candida albicans Biofilms on 3D-Printed Denture Base Resin

Rafaelly Camargo iD, Jonatas Silva de Oliveira iD, Amanda Costa Ferro iD, Beatriz Ribeiro Ribas iD, Alan Augusto Valério Alves iD, Janaina Habib Jorge iD

Journal of Fungi · 12.09.2025 · 11 (9) · 668

DOI: 10.3390/jof11090668 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Fungi, online erschienen am 12.09.2025. Verfasst von Rafaelly Camargo und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Dental Materials and Prosthodontics, School of Dentistry, São Paulo State University (UNESP), Araraquara 14801-903, São Paulo, Brazil. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 56 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: São Paulo Research Foundation (FAPESP).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Studies assessing the long-term effects of brushing with cleaning and disinfecting agents on surface roughness and biofilm accumulation on the three-dimensionally (3D) printed resins remain scarce. This study aimed to evaluate the effects of different solutions and simulated brushing times on the surface roughness and biofilm formation on heat-cured and 3D-printed denture base resins. Discs samples (10 mm × 1.2 mm) were prepared and randomly assigned to brushing treatments using the following solutions: distilled water, disinfectant liquid soap and dentifrice. The specimens (n = 9) were subjected to 10,000, 20,000 and 50,000 cycles to simulate 1, 2 and 5 years of brushing, respectively. The control group consisted of unbrushed samples. Surface roughness (Ra) was measured. Candida albicans biofilm formation was evaluated by counting colony forming units, cellular metabolic activity, and qualitative and quantitative analysis through confocal fluorescence microscopy. A significant increase in roughness was observed in both resins after two years of simulated brushing, mainly with dentifrice. After two years of brushing, an increase in the number of cells and metabolism of C. albicans was observed, in agreement with the fluorescence and biofilm thickness results. Brushing with dentifrice increased the roughness of heat-cured and 3D-printed resins and potentially increased C. albicans biofilm formation.

Schlagwörter

Stichwörter der Autor:innen

3D printingCandida albicansbrushingdenture baseroughness

Autor:innen und Institutionen

  • Department of Dental Materials and Prosthodontics, School of Dentistry, São Paulo State University (UNESP), Araraquara 14801-903, São Paulo, Brazil.

ORCID-Profile: Rafaelly Camargo, Jonatas Silva de Oliveira, Amanda Costa Ferro, Beatriz Ribeiro Ribas, Alan Augusto Valério Alves, Janaina Habib Jorge

Förderung

  • São Paulo Research Foundation (FAPESP)

Zitieren

APA

Camargo, R., Oliveira, J. S., Ferro, A. C., Ribas, B. R., Alves, A. A. V., & Jorge, J. H. (2025). Surface Changes Induced by Brushing Increase Candida albicans Biofilms on 3D-Printed Denture Base Resin. Journal of Fungi, 11(9), 668. https://doi.org/10.3390/jof11090668

Vancouver

Camargo R, Oliveira JS, Ferro AC, Ribas BR, Alves AAV, Jorge JH. Surface Changes Induced by Brushing Increase Candida albicans Biofilms on 3D-Printed Denture Base Resin. Journal of Fungi. 2025;11(9):668. doi:10.3390/jof11090668

BibTeX
@article{Camargo2025,
  author = {Camargo, Rafaelly and Oliveira, Jonatas Silva de and Ferro, Amanda Costa and Ribas, Beatriz Ribeiro and Alves, Alan Augusto Valério and Jorge, Janaina Habib},
  title = {Surface Changes Induced by Brushing Increase Candida albicans Biofilms on 3D-Printed Denture Base Resin},
  journal = {Journal of Fungi},
  year = {2025},
  volume = {11},
  number = {9},
  pages = {668},
  doi = {10.3390/jof11090668}
}
Kostenlos starten →