EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Effect of various surface treatments on relining bond strength of CAD‐CAM denture base materials

Isil Karaokutan iD, Ilayda Ayvaz

Journal of Prosthodontics · 2025-04 · 34 (4) · 422-428

DOI: 10.1111/jopr.13831 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 18.02.2024. Verfasst von Isil Karaokutan und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Dentistry, Pamukkale University, Denizli, Turkey. Hauptthemen laut MEDLINE: Denture Bases, Dental Bonding, Computer-Aided Design, Dental Materials. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

The aim of this study was to analyze the impact of various surface treatments and production methods on the shear bond strength (SBS) between reline material and denture base resins. Materials and Methods One‐hundred‐twenty specimens were produced using conventional heat‐polymerization, subtractive, and additive techniques. Each group consisted of 40 specimens. The specimens were divided into four subgroups, each with 10 samples, for surface treatments. These subgroups were: (1) Control‐only monomer application, (2) 50 μm airborne‐particle abrasion, (3) 110 μm airborne‐particle abrasion, and (4) Roughening with tungsten carbide bur. Representative specimens from each subgroup were examined under SEM. Then, auto‐polymerized resin was condensed in the center of the specimens. Specimens were subjected to thermal aging (5000 cycles at 5–55°C). The SBS test was conducted and failure loads were recorded. The data were evaluated by two‐way ANOVA and Tukey pairwise multiple comparisons method ( p < 0.05).

Results

The additively produced group showed significantly lower SBS than conventional and subtractive groups ( p < 0.001), with no significant differences between the subtractive and conventional groups. Specimens that underwent monomer application only showed the lowest SBS among surface treatments, while 50 μm airborne‐particle abrasion showed the highest SBS. Based on the partial eta‐squared analysis results, the surface treatment mainly impacted SBS.

Conclusions

Among the surface treatment methods, treating denture bases with 50 μm airborne‐particle abrasion is more effective for maintaining adhesion, especially in the additive technique.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Denture BasesDental BondingComputer-Aided DesignDental MaterialsDenture RebasingDenture LinersSurface PropertiesShear StrengthMaterials TestingDental Stress AnalysisHumans

Stichwörter der Autor:innen

3D printingadhesiongeriatric dentistrypolymersrepair materialsurface properties

Substanzen

Dental Materials

Autor:innen und Institutionen

  • Department of Prosthodontics, Faculty of Dentistry, Pamukkale University, Denizli, Turkey.

ORCID-Profile: Isil Karaokutan

Zitieren

APA

Karaokutan, I., & Ayvaz, I. (2025). Effect of various surface treatments on relining bond strength of CAD‐CAM denture base materials. Journal of Prosthodontics, 34(4), 422-428. https://doi.org/10.1111/jopr.13831

Vancouver

Karaokutan I, Ayvaz I. Effect of various surface treatments on relining bond strength of CAD‐CAM denture base materials. Journal of Prosthodontics. 2025;34(4):422-428. doi:10.1111/jopr.13831

BibTeX
@article{Karaokutan2025,
  author = {Karaokutan, Isil and Ayvaz, Ilayda},
  title = {Effect of various surface treatments on relining bond strength of CAD‐CAM denture base materials},
  journal = {Journal of Prosthodontics},
  year = {2025},
  volume = {34},
  number = {4},
  pages = {422--428},
  doi = {10.1111/jopr.13831}
}
Kostenlos starten →