EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Effect of adhesives and mechanical surface treatments on the hard relining of CAD‐CAM denture bases

Isil Karaokutan iD, Ilayda Ayvaz, Gulsum Sayin Ozel

Journal of Prosthodontics · 2024

DOI: 10.1111/jopr.13934 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, 2024. Verfasst von Isil Karaokutan und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Dentistry, Pamukkale University, Denizli, Turkey. Hauptthemen laut MEDLINE: Denture Bases, Computer-Aided Design, Dental Bonding, Denture Rebasing. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

The aim of this study was to evaluate the impact of mechanical roughening, adhesive applications, and aging on the bonding between CAD‐CAM denture base materials with distinct chemical contents and hard relining material. Materials and Methods A total of 300 denture base specimens were produced by additive, subtractive, and conventional heat‐polymerization techniques ( N = 100). The specimens have been classified into five subgroups based on the particular surface treatments administered ( n = 20): (1) Hard relining material's adhesive application (control); (2) Tungsten carbide bur application for 1 min, and hard reline material's adhesive application; (3) Airborne‐particle abrasion (APA) with 110 μm Al 2 O 3 , and hard reline material's adhesive application; (4) Scotchbond Universal application; and (5) Visio.link application. Representative specimens from each subgroup were examined under a Scanning Electron Microscope (SEM). Subsequently, self‐cure hard relining material was condensed in the center of the specimens. Half of the specimens were thermally aged with 5000 cycles at 5°C–55°C. The shear bond strength (SBS) test was performed, and failure loads were recorded. The data was evaluated by Robust ANOVA and Bonferroni test ( p < 0.05).

Results

No statistically significant difference was obtained between the production techniques ( p = 0.051). The lowest SBS was observed in the control group among surface treatments, while mechanical surface treatments and universal adhesive showed the highest SBS for both aged and non‐aged groups. Aging caused a significant decrease for all test groups ( p = 0.001).

Conclusions

Mechanical surface treatments and universal adhesive applications are more effective for maintaining adhesion across all production techniques.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Denture BasesComputer-Aided DesignDental BondingDenture RebasingAdhesivesSurface PropertiesMaterials TestingHumansDental MaterialsMicroscopy, Electron, ScanningDental Stress Analysis

Stichwörter der Autor:innen

3D printingadhesioncomputer‐aided design/computer‐aided manufacturingdenture basesgeriatric dentistryhard relining material

Substanzen

Dental MaterialsAdhesives

Autor:innen und Institutionen

  • Department of Prosthodontics, Faculty of Dentistry, Pamukkale University, Denizli, Turkey.
  • Department of Prosthodontics, Faculty of Dentistry, Istanbul Medipol University, Istanbul, Turkey.

ORCID-Profile: Isil Karaokutan

Zitieren

APA

Karaokutan, I., Ayvaz, I., & Ozel, G. S. (2024). Effect of adhesives and mechanical surface treatments on the hard relining of CAD‐CAM denture bases. Journal of Prosthodontics. https://doi.org/10.1111/jopr.13934

Vancouver

Karaokutan I, Ayvaz I, Ozel GS. Effect of adhesives and mechanical surface treatments on the hard relining of CAD‐CAM denture bases. Journal of Prosthodontics. 2024. doi:10.1111/jopr.13934

BibTeX
@article{Karaokutan2024,
  author = {Karaokutan, Isil and Ayvaz, Ilayda and Ozel, Gulsum Sayin},
  title = {Effect of adhesives and mechanical surface treatments on the hard relining of CAD‐CAM denture bases},
  journal = {Journal of Prosthodontics},
  year = {2024},
  doi = {10.1111/jopr.13934}
}
Kostenlos starten →