Effects of bone type and occlusal loading pattern on bone remodeling in implant‐supported single crown: A finite element study
Journal of Prosthodontics · 2024
DOI: 10.1111/jopr.13679 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Prosthodontics, 2024. Verfasst von Pimduen Rungsiyakull und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Dentistry, Chiang Mai University, Chiang Mai, Thailand. Hauptthemen laut MEDLINE: Dental Implants. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 42 Literaturangaben.
Abstract (Originalsprache)
Purpose
To assess the influence of bone types and loading patterns on the remodeling process over 12 months according to the variations in stress, strain, strain energy density (SED), and density allocation in the bone of implant‐supported single crown. Materials and methods A three‐dimensional finite element of a single crown implant was modeled in five different bone types (D1–D4, and grafted bone). A 200 N load was applied on an implant crown with three occlusal loading patterns (nonfunctional contact, functional contact at center, and at 2‐mm offset loading). During the first 12 months after implant placement, the SED was employed as a mechanical stimulus to simulate cortical and cancellous bone remodeling.
Results
Functional contact at 2‐mm offset loading led to a higher bone remodeling rate and stress compared to functional contact at center and nonfunctional contact. Under 2‐mm offset loading, the greatest remodeling rate after 12 months was achieved with D3 and D4, D2, grafted, and D1 cortical bone with an average peri‐implant density of 1.95, 1.77, 1.56, and 1.50 g/cm 3 , respectively. Meanwhile, the highest von Mises stresses were found in D4 (22.2 MPa) and D3 (21.9 MPa) bones.
Conclusions
A greater stress concentration and remodeling rate were found when an off‐axial load was applied on an implant placed in low bone density. Although the fastest remodeling processes resulting in increased bone density and strength were found in D3 and D4 bone types with greater off‐axial loading that may provide greater bone engagement, it could increase stress concentrations that are susceptible to inducing implant failure.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Prosthodontics, Faculty of Dentistry, Chiang Mai University, Chiang Mai, Thailand.
- Department of Mechanical Engineering, Faculty of Engineering, Chiang Mai University, Chiang Mai, Thailand.
- Sena Hospital, Dental Department, Phra Nakhon Si Ayutthaya, Thailand.
- Department of Prosthodontics, Faculty of Dentistry, Khon Kaen University, Khon Kaen, Thailand.
- Department of Dental Biomaterials, Faculty of Dentistry, Mansoura University, Mansoura, Egypt.
- Department of Restorative Science, Vision Colleges, Jeddah, Saudi Arabia.
ORCID-Profile: Pimduen Rungsiyakull, Shaymaa Elsaka
Zitieren
APA
Rungsiyakull, P., Rungsiyakull, C., Monstaporn, M., Sae-Lee, D., & Elsaka, S. (2024). Effects of bone type and occlusal loading pattern on bone remodeling in implant‐supported single crown: A finite element study. Journal of Prosthodontics. https://doi.org/10.1111/jopr.13679
Vancouver
Rungsiyakull P, Rungsiyakull C, Monstaporn M, Sae-Lee D, Elsaka S. Effects of bone type and occlusal loading pattern on bone remodeling in implant‐supported single crown: A finite element study. Journal of Prosthodontics. 2024. doi:10.1111/jopr.13679
BibTeX
@article{Rungsiyakull2024,
author = {Rungsiyakull, Pimduen and Rungsiyakull, Chaiy and Monstaporn, Montip and Sae-Lee, Daraporn and Elsaka, Shaymaa},
title = {Effects of bone type and occlusal loading pattern on bone remodeling in implant‐supported single crown: A finite element study},
journal = {Journal of Prosthodontics},
year = {2024},
doi = {10.1111/jopr.13679}
}
EUVIMED