EUVIMEDOpdag EUVIMED
Open access · CC BY 4.0

Effects of Polishing, Resin Coating, and Glaze Coating on the Surface Properties of a 3D ‐Printed Splint Resin

İzim Türker Kader iD, Ecem Karacan, Berru Kursoğlu, Pınar Kursoğlu

Journal of Esthetic and Restorative Dentistry · 2026-09 · 38 (9) · 1814-1820

DOI: 10.1111/jerd.70184 ↗

At a glance

Journal article in Journal of Esthetic and Restorative Dentistry, published online on 2026-05-05. Written by İzim Türker Kader and 3 co-authors. Institution: Department of Prosthodontics, Bahçeşehir University, School of Dental Medicine, Istanbul, Turkey. Major MEDLINE topics: Printing, Three-Dimensional, Dental Polishing, Resins, Synthetic, Occlusal Splints. Cited 1 times so far (Crossref); 32 references. The full text is freely available (open access, CC BY 4.0).

AbstractSubjectsBibliografiske oplysningerCiteRelated studies

Abstract (original language)

Objective

The objective of this in vitro study was to evaluate the effects of different surface finishing protocols and post‐curing environments on the surface roughness (Ra) and Vickers hardness (VHN) of a 3‐dimensionally (3D)‐printed occlusal splint resin. Materials and Methods Ninety‐six disc‐shaped specimens (Ø16 × 3 mm) were fabricated from a photopolymerizable splint resin using a stereolithography 3D printer. The specimens were assigned to four surface finishing groups: as‐printed (AP), polished (P), resin‐coated (RC), and glaze‐coated (GC). Each group was further subdivided according to the post‐curing environment, air (A) or glycerin (G), resulting in eight experimental groups ( n = 12): AP‐A, AP‐G, P‐A, P‐G, RC‐A, RC‐G, GC‐A, and GC‐G. Post‐curing was performed at 60°C for 60 min. For the glycerin subgroups of the coated specimens (RC‐G and GC‐G), an initial curing period in air was applied before completing the post‐curing in glycerin to stabilize the applied coating layer. Ra was measured using a surface profilometer, and VHN was determined using a microhardness tester. The data were analyzed using two‐way ANOVA and post hoc Tukey HSD test ( α = 0.05).

Results

Surface finishing significantly affected Ra and VHN ( p < 0.001), whereas the post‐curing environment had no effect ( p > 0.05). AP‐A and AP‐G specimens showed the highest Ra, while GC‐A and GC‐G specimens exhibited the highest VHN ( p < 0.001).

Conclusions

Surface finishing is essential for optimizing surface properties of 3D‐printed occlusal splints. Although coating procedures, particularly glaze, were associated with higher surface hardness, polishing yielded smoother surfaces and provided consistent and clinically acceptable properties. Clinical Significance Surface finishing plays an important role in the clinical performance of 3D‐printed occlusal splints. Although coating procedures yield high surface hardness, polishing provides smoother, more consistent surfaces, making it a practical and reliable option for routine clinical use.

Subjects

MeSH terms (MEDLINE)

Printing, Three-DimensionalDental PolishingResins, SyntheticOcclusal SplintsSurface PropertiesMaterials Testing

Substances

Resins, Synthetic

Authors and institutions

  • Department of Prosthodontics, Bahçeşehir University, School of Dental Medicine, Istanbul, Turkey.
  • Department of Prosthodontics, Yeditepe University, Faculty of Dentistry, Istanbul, Turkey.
  • Universität Witten/Herdecke, School of Dental Medicine, Witten, Germany.

ORCID profiles: İzim Türker Kader

Cite

APA

Türker Kader, İ., Karacan, E., Kursoğlu, B., & Kursoğlu, P. (2026). Effects of Polishing, Resin Coating, and Glaze Coating on the Surface Properties of a 3D ‐Printed Splint Resin. Journal of Esthetic and Restorative Dentistry, 38(9), 1814-1820. https://doi.org/10.1111/jerd.70184

Vancouver

Türker Kader İ, Karacan E, Kursoğlu B, Kursoğlu P. Effects of Polishing, Resin Coating, and Glaze Coating on the Surface Properties of a 3D ‐Printed Splint Resin. Journal of Esthetic and Restorative Dentistry. 2026;38(9):1814-1820. doi:10.1111/jerd.70184

BibTeX
@article{TrkerKader2026,
  author = {Türker Kader, İzim and Karacan, Ecem and Kursoğlu, Berru and Kursoğlu, Pınar},
  title = {Effects of Polishing, Resin Coating, and Glaze Coating on the Surface Properties of a 3D ‐Printed Splint Resin},
  journal = {Journal of Esthetic and Restorative Dentistry},
  year = {2026},
  volume = {38},
  number = {9},
  pages = {1814--1820},
  doi = {10.1111/jerd.70184}
}
Start for free →