EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access · CC BY 4.0

Comparison of three occlusal splint material systems manufactured by conventional, subtractive, and additive techniques

Mariana Farias Rocha, Isabela Vitória de Oliveira Nunes, Natasha Rohrig Assumpção da Motta, Anna Júlia Mendonça Paraíso, May Anny Alves Fraga, Cleocir José Dalmaschio, Rafael Ratto de Moraes, Nathalia Silveira Finck, Juliana Malacarne-Zanon

Clinical Oral Investigations · 09.11.2026 · 30 (12)

DOI: 10.1007/s00784-026-07250-7 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift Clinical Oral Investigations, online erschienen am 09.11.2026. Verfasst von Mariana Farias Rocha und 8 weiteren Autor:innen. Beteiligte Einrichtung: School of Dentistry, Federal University of Espírito Santo (UFES), Vitória, ES, Brazil. Hauptthemen laut MEDLINE: Occlusal Splints, Computer-Aided Design, Printing, Three-Dimensional, Dental Materials. Die Arbeit nennt 26 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Universidade Federal Do Espírito Santo.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

To compare the thermal–viscoelastic behavior, hygroscopic properties, color stability, and surface morphology of three commercial occlusal splint material systems produced by conventional heat polymerization, CAD/CAM milling, and 3D printing. The null hypothesis was that the three material systems would not differ in thermal-viscoelastic behavior, hygroscopic properties, or color stability. Surface morphology was assessed qualitatively as a complementary outcome. Materials and methods Heat-polymerized polymethyl methacrylate (HEC), CAD/CAM-milled polymethyl methacrylate (CAD-M), and a 3D-printed photopolymer resin (3DP) were evaluated. Dynamic mechanical analysis was performed to determine glass transition temperature (Tg), tan δ, and thermal heterogeneity ( n = 5). Water sorption (WS), solubility (SL), and color change after coffee immersion (ΔE00) were assessed ( n = 8). Surface morphology was qualitatively analyzed by atomic force microscopy and scanning electron microscopy.

Results

Significant differences were observed among the material systems for thermal and hygroscopic outcomes. CAD-M presented the highest mean Tg (149.58 ± 0.95 °C), the lowest water sorption (18.76 ± 0.56 µg/mm³), the lowest solubility (2.59 ± 0.48 µg/mm³), and a ΔE00 of 2.29 ± 1.20 after 7 days of coffee immersion. Conversely, 3DP showed the lowest Tg (83.18 ± 7.87 °C), highest WS (35.12 ± 0.82 µg/mm³), highest SL (6.16 ± 0.40 µg/mm³), greatest color change, and a more irregular surface morphology.

Conclusions

The three evaluated commercial material systems differed in thermal-viscoelastic behavior, hygroscopic properties, color stability, and surface morphology. Among the specific systems tested, CAD-M showed the most favorable overall laboratory profile. Because each manufacturing approach was represented by a single commercial material with a distinct composition, these differences cannot be attributed exclusively to the manufacturing route. Clinical relevance Under the in vitro conditions tested, the milled material system showed a higher glass transition temperature and lower water sorption, solubility and coffee-induced discoloration than the 3D-printed system. Whether these laboratory differences translate into differences in the clinical performance of occlusal splints was not assessed in this study.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Occlusal SplintsComputer-Aided DesignPrinting, Three-DimensionalDental MaterialsSurface PropertiesMaterials TestingPolymethyl MethacrylateMicroscopy, Electron, ScanningMicroscopy, Atomic ForceSolubilityColorViscosity

Stichwörter der Autor:innen

3D printingCAD/CAMDynamic mechanical analysisOcclusal splintsPolymethyl methacrylateWater sorption

Substanzen

Polymethyl MethacrylateDental Materials

Autor:innen und Institutionen

  • School of Dentistry, Federal University of Espírito Santo (UFES), Vitória, ES, Brazil.
  • Centro Universitário FAESA, Vitória, ES, Brazil.
  • Department of Restorative Dentistry, Endodontics and Dental Materials, Bauru School of Dentistry, University of São Paulo (FOB-USP), Bauru, SP, Brazil.
  • Department of Chemistry, Federal University of Espírito Santo (UFES), Vitória, ES, Brazil.
  • Department of Restorative Dentistry, Federal University of Pelotas (UFPel), Pelotas, RS, Brazil.
  • Department of Prosthodontics, Federal University of Espírito Santo (UFES), Vitória, ES, Brazil.

Förderung

  • Universidade Federal Do Espírito Santo

Zitieren

APA

Rocha, M. F., de Oliveira Nunes, I. V., da Motta, N. R. A., Paraíso, A. J. M., Fraga, M. A. A., Dalmaschio, C. J., de Moraes, R. R., Finck, N. S., & Malacarne-Zanon, J. (2026). Comparison of three occlusal splint material systems manufactured by conventional, subtractive, and additive techniques. Clinical Oral Investigations, 30(12). https://doi.org/10.1007/s00784-026-07250-7

Vancouver

Rocha MF, de Oliveira Nunes IV, da Motta NRA, Paraíso AJM, Fraga MAA, Dalmaschio CJ, et al. Comparison of three occlusal splint material systems manufactured by conventional, subtractive, and additive techniques. Clinical Oral Investigations. 2026;30(12). doi:10.1007/s00784-026-07250-7

BibTeX
@article{Rocha2026,
  author = {Rocha, Mariana Farias and de Oliveira Nunes, Isabela Vitória and da Motta, Natasha Rohrig Assumpção and Paraíso, Anna Júlia Mendonça and Fraga, May Anny Alves and Dalmaschio, Cleocir José and de Moraes, Rafael Ratto and Finck, Nathalia Silveira and Malacarne-Zanon, Juliana},
  title = {Comparison of three occlusal splint material systems manufactured by conventional, subtractive, and additive techniques},
  journal = {Clinical Oral Investigations},
  year = {2026},
  volume = {30},
  number = {12},
  doi = {10.1007/s00784-026-07250-7}
}
Kostenlos starten →