EUVIMEDOdkrijte EUVIMED
Systematische ÜbersichtMetaanalyseOpen access · CC BY-NC-ND 4.0

Is Additive Manufacturing of Dental Zirconia Comparable to Subtractive Methods When Considering Printing Orientation and Layer Thickness? A Systematic Review and Meta‐Analysis

Mirelle M Ruggiero iD, Letícia V S Souza iD, Marcela B Magno, Xuan Song iD, Lucianne C Maia iD, Altair A D B Cury, Yu Zhang iD

Journal of Esthetic and Restorative Dentistry · 2026-03 · 38 (3) · 604-634

DOI: 10.1111/jerd.13514 ↗

At a glance

Systematische Übersicht in Journal of Esthetic and Restorative Dentistry, published online on 2025-07-04. Written by Mirelle M Ruggiero and 6 co-authors. Institution: Department of Prosthodontics and Periodontology, Piracicaba Dental School, University of Campinas, Piracicaba, Sao Paulo, Brazil. Major MEDLINE topics: Zirconium, Dental Materials, Computer-Aided Design, Dental Prosthesis Design. Cited 13 times so far (Crossref); 90 references. The full text is freely available (open access, CC BY-NC-ND 4.0). Funded by: National Institutes of Health/National Institute of Dental and Craniofacial Research, NIDCR NIH HHS, Fundação de Amparo à Pesquisa do Estado de São Paulo.

PovzetekSubjectsBibliografski podatkiCiteRelated studies

Abstract (original language)

Objective

The aim of this systematic review and meta‐analysis was to determine whether the production of monolithic dental zirconia using additive manufacturing (AM), with consideration of different printing directions and layer thicknesses, enhances its mechanical and physical properties relative to subtractive manufacturing (SM). Methodology This systematic review followed PRISMA guidelines and was registered on the Open Science Framework. The PICO strategy was used, focusing on monolithic dental zirconia, comparing AM (stereolithography [SLA] and digital light processing [DLP]) with SM (i.e., CIPing/presintering/milling). In vitro studies were included. Electronic searches were conducted across multiple databases and gray literature, followed by data selection and extraction. Methodological quality was assessed using the QUIN tool for in vitro risk of bias. Mean and standard deviation of flexural strength, density, roughness, and specimen count per group were used to calculate the mean difference (MD) with a 95% confidence interval (CI) in the meta‐analysis.

Results

A total of 31 studies were included in the qualitative synthesis and 21 in the quantitative analysis. Most were classified as having a medium risk of bias. The meta‐analysis indicated that AM zirconia exhibited lower flexural strength than SM zirconia. However, subgroup analyses revealed no significant difference in the flexural strength of samples fabricated using SLA technology or printed at the 0° orientation relative to SM zirconia. Individually, AM zirconia fabricated with 25 or 50 μm layer thicknesses possessed lower flexural strength than SM zirconia, regardless of print direction. No differences were observed between the manufacturing methods regarding surface roughness, although SM demonstrated significantly higher density than AM zirconia.

Conclusions

AM dental zirconia demonstrated lower flexural strength when pooled across printing technologies, build orientations, and layer thicknesses. However, it exhibited comparable strength to SM zirconia at 0° or fabricated using SLA technology. Both AM and SM methods yielded similar surface roughness, with SM producing higher density. Most studies had a medium risk of bias, suggesting the need for further research and methodological rigor, particularly regarding translucency. Clinical Significance Based on current in vitro evidence, AM zirconia may show potential for posterior crowns; however, further clinical validation is needed, especially for the anterior region due to insufficient translucency to meet esthetic demands.

Subjects

MeSH terms (MEDLINE)

ZirconiumDental MaterialsComputer-Aided DesignDental Prosthesis DesignPrinting, Three-DimensionalHumansSurface PropertiesStereolithography

Author keywords

3D‐printed zirconia3Y‐TZPbuild orientationmicrostructuremilled zirconiastrengthtranslucency

Substances

Zirconiumzirconium oxideDental Materials

Authors and institutions

  • Department of Prosthodontics and Periodontology, Piracicaba Dental School, University of Campinas, Piracicaba, Sao Paulo, Brazil.
  • Laboratories for Microstructure Physics & Mechanics of Materials, Department of Preventive and Restorative Sciences, School of Dental Medicine, University of Pennsylvania, Philadelphia, Pennsylvania, USA.
  • Department of Restorative Dentistry, Piracicaba Dental School, University of Campinas, Piracicaba, Sao Paulo, Brazil.
  • Department of Pediatric Dentistry and Orthodontics, School of Dentistry, Federal University of Rio de Janeiro, Rio de Janeiro, Brazil.
  • Department of Industrial and Systems Engineering, College of Engineering, University of Iowa (UIowa), Iowa City, USA.

ORCID profiles: Mirelle M Ruggiero, Letícia V S Souza, Xuan Song, Lucianne C Maia, Yu Zhang

Funding

  • National Institutes of Health/National Institute of Dental and Craniofacial Research
  • NIDCR NIH HHS
  • Fundação de Amparo à Pesquisa do Estado de São Paulo
  • Coordenação de Aperfeiçoamento de Pessoal de Nível Superior
  • National Institute of Dental and Craniofacial Research

Cite

APA

Ruggiero, M. M., Souza, L. V. S., Magno, M. B., Song, X., Maia, L. C., Cury, A. A. D. B., & Zhang, Y. (2026). Is Additive Manufacturing of Dental Zirconia Comparable to Subtractive Methods When Considering Printing Orientation and Layer Thickness? A Systematic Review and Meta‐Analysis. Journal of Esthetic and Restorative Dentistry, 38(3), 604-634. https://doi.org/10.1111/jerd.13514

Vancouver

Ruggiero MM, Souza LVS, Magno MB, Song X, Maia LC, Cury AADB, et al. Is Additive Manufacturing of Dental Zirconia Comparable to Subtractive Methods When Considering Printing Orientation and Layer Thickness? A Systematic Review and Meta‐Analysis. Journal of Esthetic and Restorative Dentistry. 2026;38(3):604-634. doi:10.1111/jerd.13514

BibTeX
@article{Ruggiero2026,
  author = {Ruggiero, Mirelle M and Souza, Letícia V S and Magno, Marcela B and Song, Xuan and Maia, Lucianne C and Cury, Altair A D B and Zhang, Yu},
  title = {Is Additive Manufacturing of Dental Zirconia Comparable to Subtractive Methods When Considering Printing Orientation and Layer Thickness? A Systematic Review and Meta‐Analysis},
  journal = {Journal of Esthetic and Restorative Dentistry},
  year = {2026},
  volume = {38},
  number = {3},
  pages = {604--634},
  doi = {10.1111/jerd.13514}
}
Start for free →