EUVIMEDOpdag EUVIMED
Open access · CC BY-NC-ND 4.0

Mechanical properties of 3D‐printed and milled composite resins for definitive restorations: An in vitro comparison of initial strength and fatigue behavior

Elisabeth Prause, Tine Malgaj iD, Andraž Kocjan, Florian Beuer, Jeremias Hey, Peter Jevnikar, Franziska Schmidt

Journal of Esthetic and Restorative Dentistry · 2024

DOI: 10.1111/jerd.13132 ↗

At a glance

Journal article in Journal of Esthetic and Restorative Dentistry, 2024. Written by Elisabeth Prause and 6 co-authors. Institution: Department of Prosthodontics, Geriatric Dentistry and Craniomandibular Disorders, Charité-Universitätsmedizin Berlin, Berlin, Germany. Major MEDLINE topics: Composite Resins, Ceramics. Cited 71 times so far (Crossref); 65 references. The full text is freely available (open access, CC BY-NC-ND 4.0). Funded by: Javna Agencija za Raziskovalno Dejavnost RS.

AbstractSubjectsBibliografiske oplysningerCiteRelated studies

Abstract (original language)

Objective

To evaluate the flexural strength and fatigue behavior of a novel 3D‐printed composite resin for definitive restorations. Materials and Methods Fifty disc‐shaped specimens were manufactured from each of a nanohybrid composite resin (NHC), polymer‐infiltrated ceramic network (PICN), and 3D‐printed composite resin (3D) with CAD‐CAM technology. Biaxial flexural strength ( σ in ) ( n = 30 per group) and biaxial flexural fatigue strength ( σ ff ) ( n = 20 per group) were measured using piston‐on‐three‐balls method, employing a staircase approach of 10 5 cycles. Weibull statistics, relative‐strength degradation calculations, and fractography were performed. The results were analyzed with 1‐way ANOVA and Games‐Howell post hoc test ( α = 0.05).

Results

Significant differences in σ in and σ ff among the groups ( p < 0.001) were detected. The NHC group provided the highest mean ± standard deviation σ in and σ ff (237.3 ± 31.6 MPa and 141.3 ± 3.8 MPa), followed by the PICN (140.3 ± 12.9 MPa and 73.5 ± 9.9 MPa) and the 3D (83.6 ± 18.5 MPa and 37.4 ± 23.8 MPa) groups. The 3D group exhibited significantly lower Weibull modulus ( m = 4.7) and up to 15% higher relative strength degradation with areas of nonhomogeneous microstructure as possible fracture origins.

Conclusions

The 3D‐printed composite resin exhibited the lowest mechanical properties, where areas of nonhomogeneous microstructure developed during the mixing procedure served as potential fracture origins. Clinical Significance The clinical indications of the investigated novel 3D‐printed composite resin should be limited to long‐term provisional restorations. A cautious procedure for mixing the components is crucial before the 3D‐printing process, since nonhomogeneous areas developed during the mixing could act as fracture origins.

Subjects

MeSH terms (MEDLINE)

Composite ResinsCeramicsMaterials TestingFlexural StrengthPrinting, Three-DimensionalComputer-Aided DesignPolymersSurface Properties

Author keywords

3D-printed composite resinsWeibulladditive manufacturingflexural fatigue strengthflexural strengthmilled composite resinsstaircase approach

Substances

Composite ResinsPolymers

Authors and institutions

  • Department of Prosthodontics, Geriatric Dentistry and Craniomandibular Disorders, Charité-Universitätsmedizin Berlin, Berlin, Germany.
  • Department of Prosthodontics, Faculty of Medicine, University of Ljubljana, Ljubljana, Slovenia.
  • Department for Nanostructured Materials, Jožef Stefan Institute, Ljubljana, Slovenia.
  • Department of Prosthodontics, School of Dental Medicine, Martin-Luther-University, Halle, Germany.

ORCID profiles: Tine Malgaj

Funding

  • Javna Agencija za Raziskovalno Dejavnost RS

Cite

APA

Prause, E., Malgaj, T., Kocjan, A., Beuer, F., Hey, J., Jevnikar, P., & Schmidt, F. (2024). Mechanical properties of 3D‐printed and milled composite resins for definitive restorations: An in vitro comparison of initial strength and fatigue behavior. Journal of Esthetic and Restorative Dentistry. https://doi.org/10.1111/jerd.13132

Vancouver

Prause E, Malgaj T, Kocjan A, Beuer F, Hey J, Jevnikar P, et al. Mechanical properties of 3D‐printed and milled composite resins for definitive restorations: An in vitro comparison of initial strength and fatigue behavior. Journal of Esthetic and Restorative Dentistry. 2024. doi:10.1111/jerd.13132

BibTeX
@article{Prause2024,
  author = {Prause, Elisabeth and Malgaj, Tine and Kocjan, Andraž and Beuer, Florian and Hey, Jeremias and Jevnikar, Peter and Schmidt, Franziska},
  title = {Mechanical properties of 3D‐printed and milled composite resins for definitive restorations: An in vitro comparison of initial strength and fatigue behavior},
  journal = {Journal of Esthetic and Restorative Dentistry},
  year = {2024},
  doi = {10.1111/jerd.13132}
}
Start for free →