EUVIMEDEUVIMED entdecken
Vergleichsstudie

Merlon machinability and mechanical properties of four CAD/CAM block materials

Nina Attik iD, Pierre Colon iD, Brigitte Grosgogeat iD, Fatma Zohra Cherchali iD, Hazem Abouelleil iD

European Journal of Oral Sciences · 2025

DOI: 10.1111/eos.70030 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift European Journal of Oral Sciences, 2025. Verfasst von Nina Attik und 4 weiteren Autor:innen. Beteiligte Einrichtung: Laboratoire des Multimatériaux et Interfaces, UMR CNRS 5615, Univ Lyon, Université Claude Bernard Lyon 1, Villeurbanne, France. Hauptthemen laut MEDLINE: Computer-Aided Design, Dental Porcelain, Ceramics, Composite Resins. Die Arbeit nennt 54 Literaturangaben. Gefördert von: Centre Technologique des Microstructures.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The mechanical properties and machinability of CAD/CAM materials are critical in determining their clinical applications. This study evaluated and compared the mechanical behavior and machinability of three composite‐based blocks: Cerasmart (CS), Lava Ultimate (LU), and Grandio Blocs (GR), with a ceramic‐based block, Initial LRF (IR). Flexural strength, flexural modulus, fracture toughness, and Vickers hardness were assessed following standardized ISO protocols. The machinability was tested using the Merlon fracture method (ISO 18675:2022), and machined margins were examined using scanning electron microscopy (SEM). One‐way ANOVA was performed for statistical analysis ( α = 0.05). GR exhibited the highest flexural strength among the tested materials, while IR showed significantly higher flexural modulus and Vickers hardness than the other materials. CS showed the lowest fracture toughness values. SEM observations revealed clear differences in surface quality after machining, with the ceramic block IR displaying inferior edge integrity compared with the composite‐based blocks. All four materials demonstrated satisfactory machinability according to ISO standards. However, composite‐based blocks exhibited better edge quality compared with the leucite‐reinforced ceramic block. The findings indicate that composite‐based restorative materials may result in better adaptation at the dental margins in posterior restorations, whereas ceramic materials present greater hardness, making them particularly suitable for enamel replacement.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Computer-Aided DesignDental PorcelainCeramicsComposite ResinsDental MaterialsMaterials TestingMicroscopy, Electron, ScanningSurface PropertiesFlexural StrengthHardnessHumansDental Stress AnalysisElastic ModulusAluminum Silicates

Stichwörter der Autor:innen

CAD/CAM materialsMerlon testmachinabilitymechanical properties

Substanzen

Dental PorcelainComposite ResinsDental MaterialsleuciteAluminum Silicates

Autor:innen und Institutionen

  • Laboratoire des Multimatériaux et Interfaces, UMR CNRS 5615, Univ Lyon, Université Claude Bernard Lyon 1, Villeurbanne, France.
  • Faculté d'Odontologie, Univ Lyon, Université Claude Bernard Lyon 1, Lyon, France.
  • Faculté d'Odontologie, Université Paris Cité, Paris, France.
  • Service Odontologie, Hôpital Rothschild, Assistance Publique-Hôpitaux de Paris, Paris, France.
  • Service d'Odontologie, Hospices Civils de Lyon, Lyon, France.
  • Laboratoire de Synthèse Macromoléculaire et Thio-organique Macromoléculaire, Faculté de Chimie, Université des Sciences et de la Technologie Houari Boumediene, Alger, Algeria.

ORCID-Profile: Nina Attik, Pierre Colon, Brigitte Grosgogeat, Fatma Zohra Cherchali, Hazem Abouelleil

Förderung

  • Centre Technologique des Microstructures

Zitieren

APA

Attik, N., Colon, P., Grosgogeat, B., Cherchali, F. Z., & Abouelleil, H. (2025). Merlon machinability and mechanical properties of four CAD/CAM block materials. European Journal of Oral Sciences. https://doi.org/10.1111/eos.70030

Vancouver

Attik N, Colon P, Grosgogeat B, Cherchali FZ, Abouelleil H. Merlon machinability and mechanical properties of four CAD/CAM block materials. European Journal of Oral Sciences. 2025. doi:10.1111/eos.70030

BibTeX
@article{Attik2025,
  author = {Attik, Nina and Colon, Pierre and Grosgogeat, Brigitte and Cherchali, Fatma Zohra and Abouelleil, Hazem},
  title = {Merlon machinability and mechanical properties of four CAD/CAM block materials},
  journal = {European Journal of Oral Sciences},
  year = {2025},
  doi = {10.1111/eos.70030}
}
Kostenlos starten →