EUVIMEDEUVIMED entdecken
Crossref

Effects of SrO and Basicity on Structure and Thermal Properties of Fluorine‐Free Mold Fluxes for High‐Titanium Steels

Zijing Ni, Zhuo Chen, Jiajing Zhang, Yiman Chen, Weitong Du

Journal of the American Ceramic Society · 2026-06 · 109 (6)

DOI: 10.1111/jace.70936 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of the American Ceramic Society, online erschienen am 18.06.2026. Verfasst von Zijing Ni und 4 weiteren Autor:innen. Die Arbeit nennt 53 Literaturangaben. Gefördert von: National Natural Science Foundation of China, Natural Science Foundation of Jiangsu Province.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To overcome the property degradation of traditional CaO‐SiO 2 fluxes reacting with titanium for the casting of high‐titanium steel, this study introduces an eco‐friendly, fluorine‐free flux using SrO to replace CaO partially. This modification regulates the microscopic network structure of the slag melt and thereby affects its fluidity and heat‐transfer behavior. A multi‐component fluorine‐free mold flux system, CaO–SrO–SiO 2 –TiO 2 –Al 2 O 3 –B 2 O 3 –Na 2 O–MgO, was developed and its microstructural evolution and regulatory effects on macroscopic properties (viscosity and thermal conductivity) were analyzed using molecular dynamics (MD) simulations and Raman spectroscopy. The results indicate that with increasing SrO content at a constant CaO/SiO 2 ratio, the melt structure undergoes initial depolymerization followed by repolymerization, reaching its lowest degree of polymerization and minimum bridging oxygen proportion at 3.6 wt% SrO. Furthermore, variations in basicity significantly impact the network, as the CaO/SiO 2 ratio decreases from 1.08 to 0.84, the degree of network polymerization increases due to a higher proportion of SiO 2 . However, for low basicity, the amphoteric oxide Al 2 O 3 shifts from acting as a network former to a network modifier due to insufficient charge compensation from Ca 2+ , which subsequently decreases the degree of polymerization. Macroscopically, the viscosity of the slag is positively correlated with the degree of polymerization. The introduction of SrO effectively reduces the system's viscosity and flow resistance by depolymerizing the silicate network. Additionally, calculations using the reverse non‐equilibrium MD method reveal that thermal conductivity exhibits non‐monotonic fluctuations with increasing SrO content. It reaches a local minimum at 1.8 wt% due to reduced structural polymerization, and peaks at 5.4 wt% owing to the formation of stable coordination structures. Finally, as the CaO/SiO 2 ratio decreases, thermal conductivity shows a non‐monotonic response to decreasing C/S, increasing from 1.08 to 0.84 and then decreasing to 0.77.

Förderung

  • National Natural Science Foundation of China
  • Natural Science Foundation of Jiangsu Province

Zitieren

APA

Ni, Z., Chen, Z., Zhang, J., Chen, Y., & Du, W. (2026). Effects of SrO and Basicity on Structure and Thermal Properties of Fluorine‐Free Mold Fluxes for High‐Titanium Steels. Journal of the American Ceramic Society, 109(6). https://doi.org/10.1111/jace.70936

Vancouver

Ni Z, Chen Z, Zhang J, Chen Y, Du W. Effects of SrO and Basicity on Structure and Thermal Properties of Fluorine‐Free Mold Fluxes for High‐Titanium Steels. Journal of the American Ceramic Society. 2026;109(6). doi:10.1111/jace.70936

BibTeX
@article{Ni2026,
  author = {Ni, Zijing and Chen, Zhuo and Zhang, Jiajing and Chen, Yiman and Du, Weitong},
  title = {Effects of SrO and Basicity on Structure and Thermal Properties of Fluorine‐Free Mold Fluxes for High‐Titanium Steels},
  journal = {Journal of the American Ceramic Society},
  year = {2026},
  volume = {109},
  number = {6},
  doi = {10.1111/jace.70936}
}
Kostenlos starten →