EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Impact Absorption Power of Polyolefin Fused Filament Fabrication 3D ‐Printed Sports Mouthguards: In Vitro Study

Leonardo Mohamad Nassani iD, Samuel Storts, Irina Novopoltseva, Lauren Ann Place, Matthew Fogarty, Pete Schupska iD

Dental Traumatology · 2025

DOI: 10.1111/edt.13001 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Dental Traumatology, 2025. Verfasst von Leonardo Mohamad Nassani und 5 weiteren Autor:innen. Beteiligte Einrichtung: Division of Restorative and Prosthetic Dentistry, The Ohio State University College of Dentistry, Columbus, Ohio, USA. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Mouth Protectors, Polyenes, Polyvinyls. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Academy for Sports Dentistry.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background/Aim This study aims to evaluate and compare the impact absorption capacities of thermoformed ethylene vinyl acetate (EVA) mouthguards and 3D‐printed polyolefin mouthguards used in sports dentistry applications. The objective is to determine whether 3D‐printed polyolefin mouthguards offer superior impact toughness compared to traditional EVA mouthguards commonly used in sports settings. Materials and Methods Six material samples were assessed: five pressure‐formed EVA mouthguards (PolyShok, Buffalo Dental, Erkoflex, Proform, and Drufosoft) and one 3D‐printed synthetic polymer (polyolefin). The materials were evaluated using a modified American Society for Testing and Materials (ASTM) D256 Test Method A for Izod pendulum impact resistance of plastics. Polyolefin samples were 3D‐printed using fused filament fabrication (FFF) technology. Notably, the FFF process included samples printed with notches placed either parallel or perpendicular to the build direction. This orientation served as a study factor, allowing for comparison of material behavior under different printing conditions. Impact testing was conducted using an Izod impact tester to assess the materials' performance under controlled impact conditions.

Results

The study achieved a high power (1.0) in power analysis, indicating strong sensitivity to detect significant differences. Among molded materials, PolyShok showed significantly lower impact toughness compared to others ( p = 0.06). The mean impact absorption of EVA materials was 5.4 ± 0.3 kJ/m 2 , significantly lower than polyolefin materials, which demonstrated 12.9 ± 0.7 kJ/m 2 and superior performance ( p = 0.0). Horizontal‐notched polyolefin samples exhibited higher impact strength compared to vertical‐notched samples ( p = 0.009).

Conclusions

3D‐printed polyolefin mouthguards exhibited significantly higher impact toughness than thermoformed EVA mouthguards. While EVA materials demonstrated structural robustness, their lower impact resistance and observed tearing in other test specimens suggest the need for alternative testing standards to better reflect real‐world conditions. 3D‐printed mouthguards fabricated with build orientations perpendicular to the direction of impact demonstrate significantly enhanced impact absorption. Further research into manufacturing methods and testing protocols is recommended to optimize mouthguard performance under impact scenarios.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalMouth ProtectorsPolyenesPolyvinylsSports EquipmentMaterials TestingEquipment DesignHumansIn Vitro Techniques

Stichwörter der Autor:innen

additive manufacturingathlete safetyimpact absorptionmouthguardorofacial injuriespolyolefin

Substanzen

PolyenesPL 732Polyvinylsethylenevinylacetate copolymer

Autor:innen und Institutionen

  • Division of Restorative and Prosthetic Dentistry, The Ohio State University College of Dentistry, Columbus, Ohio, USA.
  • Center for Design and Manufacturing Excellence, The Ohio State University College of Engineering, Columbus, Ohio, USA.
  • Division of Dental Hygiene, The Ohio State University College of Dentistry, Columbus, Ohio, USA.

ORCID-Profile: Leonardo Mohamad Nassani, Pete Schupska

Förderung

  • Academy for Sports Dentistry

Zitieren

APA

Nassani, L. M., Storts, S., Novopoltseva, I., Place, L. A., Fogarty, M., & Schupska, P. (2025). Impact Absorption Power of Polyolefin Fused Filament Fabrication 3D ‐Printed Sports Mouthguards: In Vitro Study. Dental Traumatology. https://doi.org/10.1111/edt.13001

Vancouver

Nassani LM, Storts S, Novopoltseva I, Place LA, Fogarty M, Schupska P. Impact Absorption Power of Polyolefin Fused Filament Fabrication 3D ‐Printed Sports Mouthguards: In Vitro Study. Dental Traumatology. 2025. doi:10.1111/edt.13001

BibTeX
@article{Nassani2025,
  author = {Nassani, Leonardo Mohamad and Storts, Samuel and Novopoltseva, Irina and Place, Lauren Ann and Fogarty, Matthew and Schupska, Pete},
  title = {Impact Absorption Power of Polyolefin Fused Filament Fabrication 3D ‐Printed Sports Mouthguards: In Vitro Study},
  journal = {Dental Traumatology},
  year = {2025},
  doi = {10.1111/edt.13001}
}
Kostenlos starten →