EUVIMEDEUVIMED entdecken
Crossref

An Experimental Study on Design and Fabrication of Sports Laminate Mouthguard for Protection Against Intraoral Injuries

Fumi Mizuhashi iD, Yuko Watarai, Ryo Mizuhashi, Tatsuhiro Suzuki, Momoka Kawana, Kotono Nagata, Tomonori Niitsuma

Dental Traumatology · 2025

DOI: 10.1111/edt.13031 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Dental Traumatology, 2025. Verfasst von Fumi Mizuhashi und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Removable Prosthodontics, The Nippon Dental University School of Life Dentistry at Niigata, Niigata, Japan. Hauptthemen laut MEDLINE: Mouth Protectors, Equipment Design, Sports Equipment. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 32 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background/Aim Sports mouthguard should be designed and fabricated adequately. The purpose was to propose a criterion for fabricating sports laminate mouthguard with adequate thickness for protect orofacial structures. Materials and Methods Ethylene vinyl acetate sheet (Sports Mouthguard) was fabricated using a pressure former. Sports laminate mouthguard was designed as the first layer covered the labial, buccal, and occlusal sides, and the second layer covered the first layer. Four conditions were investigated; the combination of the sheets forming the first and second layers was 2 mm and 3 mm sheets (2 mm + 3 mm), 3 mm and 2 mm sheets (3 mm + 2 mm), 2 mm and 4 mm sheets (2 mm + 4 mm), and 4 mm and 2 mm sheets (4 mm + 2 mm). Laminate mouthguard thickness was measured at the labial, buccal, and occlusal sides. Statistical analyses were performed by two‐way ANOVA and Bonferroni method for the measurement areas and laminate conditions.

Results

Laminate mouthguard thickness was significantly differed among the measurement areas ( p < 0.01). The average thickness at the labial side was 2.83 mm (2 mm + 3 mm), 2.89 mm (3 mm + 2 mm), 3.51 mm (2 mm + 4 mm), and 3.53 mm (4 mm + 2 mm). Mouthguard thickness on the conditions of 2 mm + 4 mm and 4 mm + 2 mm became significantly larger compared to 2 mm + 3 mm and 3 mm + 2 mm at the labial, buccal, and occlusal sides ( p < 0.01). Adequate thickness could be obtained on the conditions of 2 mm + 4 mm and 4 mm + 2 mm.

Conclusions

Sports laminate mouthguard fabricated using 2 mm sheet with 4 mm sheet could offer adequate thickness at the labial, buccal, and occlusal sides. This finding would be one of the criteria for fabricating sports laminate mouthguard.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Mouth ProtectorsEquipment DesignSports EquipmentHumansPolyvinyls

Stichwörter der Autor:innen

designfabricationlaminate mouthguardprevention

Substanzen

Polyvinylsethylenevinylacetate copolymer

Autor:innen und Institutionen

  • Department of Removable Prosthodontics, The Nippon Dental University School of Life Dentistry at Niigata, Niigata, Japan.
  • Functional Occlusal Treatment, The Nippon Dental University Graduate School of Life Dentistry at Niigata, Niigata, Japan.
  • Comprehensive Dental Care, The Nippon Dental University Niigata Hospital, Niigata, Japan.

ORCID-Profile: Fumi Mizuhashi

Zitieren

APA

Mizuhashi, F., Watarai, Y., Mizuhashi, R., Suzuki, T., Kawana, M., Nagata, K., & Niitsuma, T. (2025). An Experimental Study on Design and Fabrication of Sports Laminate Mouthguard for Protection Against Intraoral Injuries. Dental Traumatology. https://doi.org/10.1111/edt.13031

Vancouver

Mizuhashi F, Watarai Y, Mizuhashi R, Suzuki T, Kawana M, Nagata K, et al. An Experimental Study on Design and Fabrication of Sports Laminate Mouthguard for Protection Against Intraoral Injuries. Dental Traumatology. 2025. doi:10.1111/edt.13031

BibTeX
@article{Mizuhashi2025,
  author = {Mizuhashi, Fumi and Watarai, Yuko and Mizuhashi, Ryo and Suzuki, Tatsuhiro and Kawana, Momoka and Nagata, Kotono and Niitsuma, Tomonori},
  title = {An Experimental Study on Design and Fabrication of Sports Laminate Mouthguard for Protection Against Intraoral Injuries},
  journal = {Dental Traumatology},
  year = {2025},
  doi = {10.1111/edt.13031}
}
Kostenlos starten →