Effect of different materials for conventional and 3D ‐printed models on the mechanical properties of ethylene‐vinyl acetate utilized for fabricating custom‐fit mouthguards
Dental Traumatology · 2024
DOI: 10.1111/edt.12912 ↗Kurz gefasst
Fachartikel in der Zeitschrift Dental Traumatology, 2024. Verfasst von Airin Karelys Avendaño Rondón und 4 weiteren Autor:innen. Beteiligte Einrichtung: School of Dentistry, Federal University of Uberlândia, Uberlândia, Minas Gerais, Brazil. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Mouth Protectors, Polyvinyls, Models, Dental. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 37 Literaturangaben. Gefördert von: Conselho Nacional de Desenvolvimento Científico e Tecnológico, Coordenação de Aperfeiçoamento de Pessoal de Nível Superior, Fundação de Amparo à Pesquisa do Estado de Minas Gerais.
Abstract (Originalsprache)
Background/Aim The interaction between the ethylene‐vinyl acetate (EVA) with distinct materials utilized for obtaining dental models can affect the performance of resulting mouthguards. This study attempted to evaluate the effect of different materials for conventional (dental stone) or 3D‐printed (resin) models on EVA's physical and mechanical properties and surface characteristics. Material and Methods EVA sheets (Bioart) were laminated over four model types: GIV, conventional Type IV dental stone model (Zhermak); ReG, resin‐reinforced Type IV dental stone model (Zero Stone); 3DnT, 3D resin printed model (Anycubic) without surface treatment; 3DT, 3D‐printed model (Anycubic) with water‐soluble gel (KY Jelly Lubricant, Johnson & Johnson) coating during post‐curing process. The EVA specimens were cut following the ISO 37‐II standard ( n = 30). Shore A hardness was measured before and after plasticization on the contact (internal) or opposite (external) surfaces with the model. The breaking force (F, N), elongation (EL, mm), and ultimate tensile strength (UTS, MPa) were measured using a universal testing machine. Macro‐photography and scanning electron microscopy were adopted for classifying the EVA surface alteration. Data were analyzed by one‐way ANOVA with repeated measures, followed by Tukey's test ( α = .05).
Results
Plasticization significantly decreased Shore A values for the tested EVA regardless of the model type ( p < .001). Higher F, El, and UTS values were verified for the EVA with 3DT and GIV models compared to ReG and 3DnT ( p < .001). 3DnT models resulted in severe surface alteration and a greater reduction of the mechanical properties of the EVA.
Conclusion
The interaction of EVA with 3D resin‐printed models without surface treatment or resin‐reinforced Type IV dental stone models significantly affected the physical and mechanical properties of this material. The utilization of water‐soluble gel coating during the post‐curing process of 3D resin printed models improved the mechanical properties of the EVA, similarly when this material was plasticized over conventional Type IV dental stone model.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- School of Dentistry, Federal University of Uberlândia, Uberlândia, Minas Gerais, Brazil.
- Department of Periodontology and Implantology, School of Dentistry, Universidade de Uberlândia, Uberlândia, Minas Gerais, Brazil.
- Department of Occlusion and Prosthodontic, School of Dentistry, Universidade de Uberlândia, Uberlândia, Minas Gerais, Brazil.
- Department of Operative Dentistry and Dental Materials, School of Dentistry, Universidade de Uberlândia, Uberlândia, Minas Gerais, Brazil.
ORCID-Profile: Airin Karelys Avendaño Rondón, Maribí Isomar Terán Lozada, Priscilla Barbosa Ferreira Soares, Luis Henrique Araujo Raposo, Carlos José Soares
Förderung
- Conselho Nacional de Desenvolvimento Científico e Tecnológico
- Coordenação de Aperfeiçoamento de Pessoal de Nível Superior
- Fundação de Amparo à Pesquisa do Estado de Minas Gerais
Zitieren
APA
Rondón, A. K. A., Lozada, M. I. T., Soares, P. B. F., Raposo, L. H. A., & Soares, C. J. (2024). Effect of different materials for conventional and 3D ‐printed models on the mechanical properties of ethylene‐vinyl acetate utilized for fabricating custom‐fit mouthguards. Dental Traumatology. https://doi.org/10.1111/edt.12912
Vancouver
Rondón AKA, Lozada MIT, Soares PBF, Raposo LHA, Soares CJ. Effect of different materials for conventional and 3D ‐printed models on the mechanical properties of ethylene‐vinyl acetate utilized for fabricating custom‐fit mouthguards. Dental Traumatology. 2024. doi:10.1111/edt.12912
BibTeX
@article{Rondn2024,
author = {Rondón, Airin Karelys Avendaño and Lozada, Maribí Isomar Terán and Soares, Priscilla Barbosa Ferreira and Raposo, Luis Henrique Araujo and Soares, Carlos José},
title = {Effect of different materials for conventional and 3D ‐printed models on the mechanical properties of ethylene‐vinyl acetate utilized for fabricating custom‐fit mouthguards},
journal = {Dental Traumatology},
year = {2024},
doi = {10.1111/edt.12912}
}
EUVIMED