EUVIMEDEUVIMED entdecken
Open Access

Numerical Homogenization Calculation of Effective Stiffness of Fused Deposition Modeling Printing Carbon Fiber Reinforced Polylactic Acid Composites

Mingju Lei, Yanen Wang iD, Qinghua Wei, Mingyang Li, Juan Zhang, Yanmei Wang

3D Printing and Additive Manufacturing · 01.10.2024 · 11 (5) · 1863-1876

DOI: 10.1089/3dp.2023.0131 ↗

Kurz gefasst

Fachartikel in der Zeitschrift 3D Printing and Additive Manufacturing, online erschienen am 22.10.2024. Verfasst von Mingju Lei und 5 weiteren Autor:innen. Beteiligte Einrichtung: Industry Engineering Department, School of Mechanical Engineering, Northwestern Polytechnical University, Xi'an, P.R. China. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The varied material and the inherent complex microstructure make predicting the effective stiffness of fused deposition modeling (FDM) printed polylactic acid (PLA)/carbon fiber (CF) composite a troublesome problem. This article proposes a microstructure scanning electron microscope (SEM) mapping modeling and numerical mean procedure to calculate the effective stiffness of FDM printing PLA/CF laminates. The printed PLA/CF parts were modeled as a continuum of 3D uniform linear elasticity with orthotropic anisotropy, and their elastic behavior was characterized by orthotropic constitutive relations. Micromechanical models of two typical deposition configurations, 0° unidirectional aligned configuration and 0°/90° angle-ply configuration of the printed parts were established based on the periodic representative volume element (RVE) technique. The elastic constants of the RVE models were estimated by volume average method in the finite element stress analysis, and the effects of deposition configurations, CF length, and content on the effective stiffness were also investigated. The results show that the effective stiffness of FDM printing PLA/CF composite is closely related to CF length, content, and the deposition configuration. With the increase of CF length and content, the Young's modulus and shear modulus of printed PLA/CF parts increase, whereas Poisson's ratio decreases. The printed PLA/CF parts with 0° unidirectional aligned configuration exhibits orthotropic characteristics, and the maximum Young's modulus appears along the first axis. The 0°/90° angle-ply FDM PLA/CF composite exhibits transverse isotropic characteristics and the lowest Young's modulus is found along the thickness direction.

Schlagwörter

Stichwörter der Autor:innen

3D printingPLA/CF compositesRVEdeposition configurationeffective stiffnessnumerical homogenization

Autor:innen und Institutionen

  • Industry Engineering Department, School of Mechanical Engineering, Northwestern Polytechnical University, Xi'an, P.R. China.
  • School of Mechatronic Engineering, Xinjiang Institute of Engineering, Urumqi, China.

ORCID-Profile: Yanen Wang

Zitieren

APA

Lei, M., Wang, Y., Wei, Q., Li, M., Zhang, J., & Wang, Y. (2024). Numerical Homogenization Calculation of Effective Stiffness of Fused Deposition Modeling Printing Carbon Fiber Reinforced Polylactic Acid Composites. 3D Printing and Additive Manufacturing, 11(5), 1863-1876. https://doi.org/10.1089/3dp.2023.0131

Vancouver

Lei M, Wang Y, Wei Q, Li M, Zhang J, Wang Y. Numerical Homogenization Calculation of Effective Stiffness of Fused Deposition Modeling Printing Carbon Fiber Reinforced Polylactic Acid Composites. 3D Printing and Additive Manufacturing. 2024;11(5):1863-1876. doi:10.1089/3dp.2023.0131

BibTeX
@article{Lei2024,
  author = {Lei, Mingju and Wang, Yanen and Wei, Qinghua and Li, Mingyang and Zhang, Juan and Wang, Yanmei},
  title = {Numerical Homogenization Calculation of Effective Stiffness of Fused Deposition Modeling Printing Carbon Fiber Reinforced Polylactic Acid Composites},
  journal = {3D Printing and Additive Manufacturing},
  year = {2024},
  volume = {11},
  number = {5},
  pages = {1863--1876},
  doi = {10.1089/3dp.2023.0131}
}
Kostenlos starten →