EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Fused-Deposition Modeling 3D Printing of Short-Cut Carbon-Fiber-Reinforced PA6 Composites for Strengthening, Toughening, and Light Weighting

Bin Sun, Suhail Mubarak, Guocun Zhang, Kangming Peng, Xueling Hu, Qia Zhang, Lixin Wu, Jianlei Wang

Polymers · 11.09.2023 · 15 (18) · 3722

DOI: 10.3390/polym15183722 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 11.09.2023. Verfasst von Bin Sun und 7 weiteren Autor:innen. Beteiligte Einrichtung: CAS Key Laboratory of Design and Assembly of Functional Nanostructures, Fujian Key Laboratory of Nanomaterials, Fujian Institute of Research on the S…. Die Arbeit wurde bisher 48-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ningbo public welfare science and technology planning project, regional development project of Fujian, Beilun District Key Core Technology Research Project.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Additive manufacturing of carbon-fiber-reinforced polymer (CFRP) has been widely used in many fields. However, issues such as inconsistent fiber orientation distribution and void formation during the layer stacking process have hindered the further optimization of the composite material’s performance. This study aimed to address these challenges by conducting a comprehensive investigation into the influence of carbon fiber content and printing parameters on the micro-morphology, thermal properties, and mechanical properties of PA6-CF composites. Additionally, a heat treatment process was proposed to enhance the interlayer bonding and tensile properties of the printed composites in the printing direction. The experimental results demonstrate that the PA6-CF25 composite achieved the highest tensile strength of 163 MPa under optimal heat treatment conditions: 120 °C for 7.5 h. This corresponds to a significant tensile strength enhancement of 406% compared to the unreinforced composites, which represents the highest reported improvement in the current field of CFRP-fused deposition 3D printing. Additionally, we have innovatively developed a single-layer monofilament CF-OD model to quantitatively analyze the influence of fiber orientation distribution on the properties of the composite material. Under specific heat treatment conditions, the sample exhibits an average orientation angle μ of 0.43 and an orientation angle variance of 8.02. The peak frequency of fiber orientation closely aligns with 0°, which corresponds to the printing direction. Finally, the study explored the lightweight applications of the composite material, showcasing the impressive specific energy absorption (SEA) value of 17,800 J/kg when implementing 3D-printed PA6-CF composites as fillers in automobile crash boxes.

Schlagwörter

Stichwörter der Autor:innen

crash boxfiber reinforced compositesfused deposition 3D printingheat treatment processhoneycomb structureorientation distributionpolyamide

Autor:innen und Institutionen

  • CAS Key Laboratory of Design and Assembly of Functional Nanostructures, Fujian Key Laboratory of Nanomaterials, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou 350002, China.
  • University of Chinese Academy of Sciences, Beijing 100049, China.
  • CAS Haixi Industrial Technology Innovation Center in Beilun, Ningbo 315830, China.
  • State Key Laboratory of Fluid Power & Mechatronic System, Key Laboratory of Soft Machines and Smart Devices of Zhejiang Province, Center for X-Mechanics, Department of Engineering Mechanics, Zhejiang University, Hangzho…
  • School of Automotive Engineering, Dalian University of Technology, Dalian 116024, China.
  • College of Chemistry and Materials Science, Fujian Normal University, Fuzhou 350007, China.

Förderung

  • Ningbo public welfare science and technology planning project
  • regional development project of Fujian
  • Beilun District Key Core Technology Research Project
  • Major Project of Science and Technology in Fuzhou
  • Fuzhou Foreign Science and Technology Cooperation Project

Zitieren

APA

Sun, B., Mubarak, S., Zhang, G., Peng, K., Hu, X., Zhang, Q., Wu, L., & Wang, J. (2023). Fused-Deposition Modeling 3D Printing of Short-Cut Carbon-Fiber-Reinforced PA6 Composites for Strengthening, Toughening, and Light Weighting. Polymers, 15(18), 3722. https://doi.org/10.3390/polym15183722

Vancouver

Sun B, Mubarak S, Zhang G, Peng K, Hu X, Zhang Q, et al. Fused-Deposition Modeling 3D Printing of Short-Cut Carbon-Fiber-Reinforced PA6 Composites for Strengthening, Toughening, and Light Weighting. Polymers. 2023;15(18):3722. doi:10.3390/polym15183722

BibTeX
@article{Sun2023,
  author = {Sun, Bin and Mubarak, Suhail and Zhang, Guocun and Peng, Kangming and Hu, Xueling and Zhang, Qia and Wu, Lixin and Wang, Jianlei},
  title = {Fused-Deposition Modeling 3D Printing of Short-Cut Carbon-Fiber-Reinforced PA6 Composites for Strengthening, Toughening, and Light Weighting},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {18},
  pages = {3722},
  doi = {10.3390/polym15183722}
}
Kostenlos starten →