EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Influence of Thermal Cycling on Friction, Wear, and Damage Evolution of Fused Deposition Modeling of 3D‐Printed Glass Fiber Reinforced Polylactic Acid Composites

Sinan Fidan, Satılmış Ürgün, Nevin Gamze Karsli, Taner Yılmaz, Mustafa Özgür Bora, Mehmet İskender Özsoy

Polymer Composites · 20.09.2026 · 47 (18) · 16212-16232

DOI: 10.1002/pc.71345 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymer Composites, online erschienen am 26.06.2026. Verfasst von Sinan Fidan und 5 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This research work investigated the effect of the cyclic thermo‐hygrometric aging regime between −20°C and +40°C with 0–400 cycles on the reciprocating tribological properties of fused deposition modeling (FDM) printed polylactic acid (PLA) and the same material reinforced with 10 wt.% and 15 wt.% of glass fiber GF. The samples were analyzed for wear through non‐contact laser profilometry, scanning electron microscopy, and thermal gravimetric analysis. The neat PLA showed a non‐monotonic wear profile since it was observed that the wear volume of this material increased drastically from 0.033 to 0.335 mm 3 after 200 cycles at 10 N, and finally, achieved a maximum value of 2.042 mm 3 after 400 cycles subjected to 20 N. However, the reinforcing GF changed such profile, reducing by up to 83% the wear volume. The most interesting result is that the combination of 15 wt.% of GF in a polymer subjected to 200 cycles produced a regime where the coefficient of friction (COF) was greater than unity (1.37), despite having no increase in the volumetric wear loss (Δ = 4.5%). Therefore, it is possible to conclude that there is a decoupling between the processes due to debonding of the interfaces and the third‐body wear mechanism. Factorial ANOVA ( R 2 = 99.32%) showed that Material × Cycle × Load interaction (29.39%) was the main contribution to this effect.

Zitieren

APA

Fidan, S., Ürgün, S., Karsli, N. G., Yılmaz, T., Bora, M. Ö., & Özsoy, M. İ. (2026). Influence of Thermal Cycling on Friction, Wear, and Damage Evolution of Fused Deposition Modeling of 3D‐Printed Glass Fiber Reinforced Polylactic Acid Composites. Polymer Composites, 47(18), 16212-16232. https://doi.org/10.1002/pc.71345

Vancouver

Fidan S, Ürgün S, Karsli NG, Yılmaz T, Bora MÖ, Özsoy Mİ. Influence of Thermal Cycling on Friction, Wear, and Damage Evolution of Fused Deposition Modeling of 3D‐Printed Glass Fiber Reinforced Polylactic Acid Composites. Polymer Composites. 2026;47(18):16212-16232. doi:10.1002/pc.71345

BibTeX
@article{Fidan2026,
  author = {Fidan, Sinan and Ürgün, Satılmış and Karsli, Nevin Gamze and Yılmaz, Taner and Bora, Mustafa Özgür and Özsoy, Mehmet İskender},
  title = {Influence of Thermal Cycling on Friction, Wear, and Damage Evolution of Fused Deposition Modeling of 3D‐Printed Glass Fiber Reinforced Polylactic Acid Composites},
  journal = {Polymer Composites},
  year = {2026},
  volume = {47},
  number = {18},
  pages = {16212--16232},
  doi = {10.1002/pc.71345}
}
Infokarte | EUVIMED

Artikeldaten derzeit nicht verfügbar.

Recherche