EUVIMEDEUVIMED entdecken
Crossref

Effect of finish line design and cementation on fracture resistance of 3D printed definitive crowns

Yigit Omur, Muhittin Toman, Ovul Kumbuloglu, Murat Mutluay, Arzu Tezvergil Mutluay

The Journal of Prosthetic Dentistry · 2026

DOI: 10.1016/j.prosdent.2025.11.016 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2026. Verfasst von Yigit Omur und 4 weiteren Autor:innen. Beteiligte Einrichtung: Doctoral student, Department of Prosthetic Dentistry, Faculty of Dentistry, Ege University, Izmir, Turkey; and Researcher, Department of Restorative …. Hauptthemen laut MEDLINE: Crowns, Printing, Three-Dimensional, Cementation, Dental Prosthesis Design. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 52 Literaturangaben. Gefördert von: TÜBİTAK.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: While 3-dimensional (3D) printing has emerged as a suitable technique for fabricating definitive restorations, the influence of cervical finish line design, cementation strategy, and artificial aging on fracture resistance remains unclear. PURPOSE: This in vitro study aimed to identify the optimal preparation design and cementation method based on the fracture resistance of 3D printed definitive premolar crowns immediately or after aging. MATERIAL AND METHODS: A total of 120 3D printed definitive crowns were fabricated using printing resin fortified with ceramic fillers for extracted maxillary premolars and divided into 12 test groups (n=10). Tooth preparations included chamfer, shoulder, or knife edge designs with uniform occlusal reduction and convergence angles. Crowns were cemented either with self-adhesive resin cement or conventional glass ionomer cement and tested after either 24 hours or after artificial aging (1 200 000 load cycles, 10 000 thermocycles and 6-month water storage). Fracture resistance was evaluated using a universal testing machine. Acoustic emission (AE) analysis was used to detect initial crack propagation and initial failure. Failure modes were assessed using stereomicroscopy and scanning electron microscopy (SEM). Statistical analysis was performed with a 3-way ANOVA (α=.05). RESULTS: No statistically significant differences were found in initial failure loads (P>.05). Final fracture resistance was significantly influenced by the cement type (P=.012) and aging (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

CrownsPrinting, Three-DimensionalCementationDental Prosthesis DesignDental Restoration FailureHumansDental Stress AnalysisIn Vitro TechniquesResin CementsMaterials TestingGlass Ionomer CementsBicuspidComputer-Aided DesignMicroscopy, Electron, ScanningTooth Preparation, Prosthodontic

Substanzen

Resin CementsGlass Ionomer Cements

Autor:innen und Institutionen

  • Doctoral student, Department of Prosthetic Dentistry, Faculty of Dentistry, Ege University, Izmir, Turkey; and Researcher, Department of Restorative Dentistry and Cariology, Adhesive Dentistry Research Group, Institute…
  • Full Professor, Department of Prosthetic Dentistry, Faculty of Dentistry, Ege University, Izmir, Turkey.
  • Full Professor, Department of Oral and Maxillofacial Diseases, Faculty of Medicine, University of Helsinki, Helsinki, Finland.
  • Full Professor and Head of Department, Department of Restorative Dentistry and Cariology, Adhesive Dentistry Research Group, Institute of Dentistry, University of Turku, Turku, Finland; and Full Professor, Turku Univers…

Förderung

  • TÜBİTAK

Zitieren

APA

Omur, Y., Toman, M., Kumbuloglu, O., Mutluay, M., & Mutluay, A. T. (2026). Effect of finish line design and cementation on fracture resistance of 3D printed definitive crowns. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2025.11.016

Vancouver

Omur Y, Toman M, Kumbuloglu O, Mutluay M, Mutluay AT. Effect of finish line design and cementation on fracture resistance of 3D printed definitive crowns. The Journal of Prosthetic Dentistry. 2026. doi:10.1016/j.prosdent.2025.11.016

BibTeX
@article{Omur2026,
  author = {Omur, Yigit and Toman, Muhittin and Kumbuloglu, Ovul and Mutluay, Murat and Mutluay, Arzu Tezvergil},
  title = {Effect of finish line design and cementation on fracture resistance of 3D printed definitive crowns},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2026},
  doi = {10.1016/j.prosdent.2025.11.016}
}
Kostenlos starten →