EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of material and antagonist type on the wear of occlusal devices with different compositions fabricated by using conventional, additive, and subtractive manufacturing

Gökçen Ateş, Münir Demirel, Mustafa Borga Donmez, Süleyman Çağatay Dayan, Tonguç Sülün

The Journal of Prosthetic Dentistry · 2024

DOI: 10.1016/j.prosdent.2024.03.026 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2024. Verfasst von Gökçen Ateş und 4 weiteren Autor:innen. Beteiligte Einrichtung: Postdoctoral Research Associate, Department of Prosthodontics, Faculty of Dentistry, Istanbul University, Istanbul, Turkey; and ITI Scholar, Departme…. Hauptthemen laut MEDLINE: Materials Testing, Dental Materials, Polymethyl Methacrylate, Zirconium. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Additive (AM) and subtractive (SM) manufacturing have become popular for fabricating occlusal devices with materials of different chemical compositions. However, knowledge on the effect of material and antagonist type on the wear characteristics of occlusal devices fabricated by using different methods is limited. PURPOSE: The purpose of this in vitro study was to evaluate the effect of material and antagonist type on the wear of occlusal devices fabricated by using conventional manufacturing, AM, and SM. MATERIAL AND METHODS: Two-hundred and forty Ø10×2-mm disk-shaped specimens were fabricated by using heat-polymerized polymethylmethacrylate (control, CM), AM clear device resin fabricated in 3 different orientations (horizontal [AMH], diagonal [AMD], and vertical [AMV]), SM polymethylmethacrylate (SMP), and SM ceramic-reinforced polyetheretherketone (SMB) (n=40). Specimens were then divided into 4 groups based on the antagonists: steatite ceramic (SC); multilayered zirconia (ZR); lithium disilicate (EX); and zirconia-reinforced lithium silicate (ZLS) used for thermomechanical aging (n=10). After aging, the volume loss (mm3) and maximum wear depth (μm) were digitally evaluated. Data were analyzed with 2-way analysis of variance and Tukey honestly significant difference tests (α=.05). RESULTS: The interaction between the device material and the antagonist affected volume loss and maximum depth of wear (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Materials TestingDental MaterialsPolymethyl MethacrylateZirconiumCeramicsHumansIn Vitro TechniquesOcclusal SplintsDental Restoration WearDental Prosthesis DesignBenzophenonesDental PorcelainPolymersSurface PropertiesPolyethylene GlycolsKetones

Substanzen

Dental MaterialsPolymethyl MethacrylateZirconiumzirconium oxideBenzophenonesDental PorcelainpolyetheretherketonePolymerslithia disilicatePolyethylene Glycols

Autor:innen und Institutionen

  • Postdoctoral Research Associate, Department of Prosthodontics, Faculty of Dentistry, Istanbul University, Istanbul, Turkey; and ITI Scholar, Department of Prosthodontics, University of São Paulo (USP), São Paulo, Brazil.
  • Assistant Professor, Department of Prosthodontics, Faculty of Dentistry, Biruni University, Istanbul, Turkey.
  • Associate Professor, Department of Prosthodontics, Faculty of Dentistry, Istinye Univeristy, İstanbul, Turkey; and ITI Scholar, Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, Univer…
  • Associate Professor, Program of Dental Technicians, Istanbul University-Cerrahpasa, Istanbul, Turkey.
  • Professor, Department of Prosthodontics, Faculty of Dentistry, Istanbul University, Istanbul, Turkey.

Zitieren

APA

Ateş, G., Demirel, M., Donmez, M. B., Dayan, S. Ç., & Sülün, T. (2024). Effect of material and antagonist type on the wear of occlusal devices with different compositions fabricated by using conventional, additive, and subtractive manufacturing. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2024.03.026

Vancouver

Ateş G, Demirel M, Donmez MB, Dayan SÇ, Sülün T. Effect of material and antagonist type on the wear of occlusal devices with different compositions fabricated by using conventional, additive, and subtractive manufacturing. The Journal of Prosthetic Dentistry. 2024. doi:10.1016/j.prosdent.2024.03.026

BibTeX
@article{Ate2024,
  author = {Ateş, Gökçen and Demirel, Münir and Donmez, Mustafa Borga and Dayan, Süleyman Çağatay and Sülün, Tonguç},
  title = {Effect of material and antagonist type on the wear of occlusal devices with different compositions fabricated by using conventional, additive, and subtractive manufacturing},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2024},
  doi = {10.1016/j.prosdent.2024.03.026}
}
Kostenlos starten →