EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of tooth preparation design on fracture load and fracture behavior of deciduous crowns fabricated by subtractive and additive manufacturing

Misaki Hamashima, Kanae Wada, Shinya Oishi, Hidekazu Takahashi, Kaori Kohi, Daiki Kondo, Yujeong Shin, Yuika Yamanaka, Atsushi Oishi, Asuna Sugimoto, Kanako Kishima, Yumiko Nakashima und 2 weitere

Clinical Oral Investigations · 2026

DOI: 10.1007/s00784-026-07127-9 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Clinical Oral Investigations, 2026. Verfasst von Misaki Hamashima und 13 weiteren Autor:innen. Beteiligte Einrichtung: Department of Pediatric Dentistry/Special Needs Dentistry, Division of Oral Health Sciences, Graduate School of Medical and Dental Sciences, Institut…. Hauptthemen laut MEDLINE: Crowns, Computer-Aided Design, Tooth, Deciduous, Dental Prosthesis Design. Die Arbeit nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Japan Society for the Promotion of Science.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

This study evaluated the effects of crown material and margin design on fracture load and behavior of computer-aided design/computer-aided manufacturing (CAD-CAM) crowns for deciduous molars.

Methods

Three subtractive-manufacturing (SM) materials and two additive-manufacturing (AM) materials were evaluated. Crowns with knife-edge, chamfer, and deep chamfer margins were fabricated and bonded to standardized deciduous molar abutments ( n = 12/group; total = 180). Fracture load was measured under static loading, and fracture modes were classified by repairability and abutment involvement. Fracture surfaces and crack propagation were examined by scanning electron microscopy.

Results

Significant effects of material and material–margin interactions were observed ( p < 0.05). ESTELITE BLOCK II exhibited the highest fracture load with knife-edge margins, whereas Detax showed the highest values with deep chamfer margins. However, non-repairable abutment-involving fractures occurred in both materials with knife-edge margins. CERASMART PRIME showed lower fracture load but mainly repairable fractures. SHOFU BLOCK HC and CERASMART PRIME, unified crown–abutment fracture in ESTELITE BLOCK II, interlayer delamination in Detax, and superficial radial cracking in NextDent.

Conclusions

The effects of margin design on fracture load and fracture behavior were material-dependent. Among subtractive-manufacturing materials, fracture load was generally consistent with reported mechanical properties, whereas fracture behavior in additive-manufacturing materials may have been influenced by internal structure and build orientation. Material selection should consider fracture load, fracture severity, and abutment involvement. Clinical relevance Material and margin selection influence fracture resistance and failure patterns. Fracture severity and abutment involvement should be considered in addition to fracture load.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

CrownsComputer-Aided DesignTooth, DeciduousDental Prosthesis DesignDental Restoration FailureTooth Preparation, ProsthodonticMicroscopy, Electron, ScanningDental Stress AnalysisHumansMaterials TestingSurface PropertiesMolarDental Abutments

Stichwörter der Autor:innen

Additive manufacturingCAD-CAMDeciduous crownsFracture behaviorFracture loadSubtractive-manufacturing

Autor:innen und Institutionen

  • Department of Pediatric Dentistry/Special Needs Dentistry, Division of Oral Health Sciences, Graduate School of Medical and Dental Sciences, Institute of Science Tokyo, 1-5-45 Yushima, Bunkyo-ku, Tokyo, Japan.
  • Department of Pediatric Dentistry/Special Needs Dentistry, Division of Oral Health Sciences, Graduate School of Medical and Dental Sciences, Institute of Science Tokyo, 1-5-45 Yushima, Bunkyo-ku, Tokyo, Japan. wadadohs@…
  • Department of Oral and Maxillofacial Rehabilitation, Prosthodontics, Institute of Science Tokyo, Tokyo, Japan.
  • Department of Oral Biomedical Engineering, Graduate School of Medical and Dental Sciences, Institute of Science Tokyo, Tokyo, Japan.

Förderung

  • Japan Society for the Promotion of Science

Zitieren

APA

Hamashima, M., Wada, K., Oishi, S., Takahashi, H., Kohi, K., Kondo, D., Shin, Y., Yamanaka, Y., Oishi, A., Sugimoto, A., Kishima, K., Nakashima, Y., Kurogoshi, R., & Iwamoto, T. (2026). Effect of tooth preparation design on fracture load and fracture behavior of deciduous crowns fabricated by subtractive and additive manufacturing. Clinical Oral Investigations. https://doi.org/10.1007/s00784-026-07127-9

Vancouver

Hamashima M, Wada K, Oishi S, Takahashi H, Kohi K, Kondo D, et al. Effect of tooth preparation design on fracture load and fracture behavior of deciduous crowns fabricated by subtractive and additive manufacturing. Clinical Oral Investigations. 2026. doi:10.1007/s00784-026-07127-9

BibTeX
@article{Hamashima2026,
  author = {Hamashima, Misaki and Wada, Kanae and Oishi, Shinya and Takahashi, Hidekazu and Kohi, Kaori and Kondo, Daiki and Shin, Yujeong and Yamanaka, Yuika and Oishi, Atsushi and Sugimoto, Asuna and Kishima, Kanako and Nakashima, Yumiko and Kurogoshi, Rika and Iwamoto, Tsutomu},
  title = {Effect of tooth preparation design on fracture load and fracture behavior of deciduous crowns fabricated by subtractive and additive manufacturing},
  journal = {Clinical Oral Investigations},
  year = {2026},
  doi = {10.1007/s00784-026-07127-9}
}
Kostenlos starten →