EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

An Investigation into the Friction Stir Spot Welding Behavior of 3D-Printed Glass Fiber-Reinforced Polylactic Acid

Emre Kanlı, Oğuz Koçar iD, Nergizhan Anaç iD

Polymers · 24.04.2026 · 18 (9) · 1041

DOI: 10.3390/polym18091041 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 24.04.2026. Verfasst von Emre Kanlı und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Faculty of Engineering, Zonguldak Bülent Ecevit University, Zonguldak 67100, Türkiye. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 71 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The production of fiber-reinforced polymer composites using 3D printing technology offers significant potential and opportunities for industrial applications. However, current dimensional limitations in 3D printing necessitate the use of joining techniques to obtain larger components. Recently, innovative strategies such as friction stir spot welding (FSSW) have attracted considerable attention for joining polymer composites due to their ability to produce strong joints with relatively low heat input (solid-state welding). Nevertheless, it is important to understand how the fibers present in fiber-reinforced polymer composites influence material flow and welding performance during the FSSW process. In this study, glass fiber-reinforced polylactic acid (PLA-GF) composite samples produced using a 3D printer were joined by means of FSSW. Five different tool rotational speeds (900, 1200, 1500, 1800, and 2100 rpm) and three different plunge rates (10, 20, and 30 mm/min) were employed during the welding process. Mechanical tests were performed on the welded joints to investigate the relationship between the welding parameters and the resulting mechanical properties. In addition, microstructural analyses were conducted to examine the formation of welding defects. The results revealed that three distinct zones were formed in the material after the FSSW process: the stir zone, mixed zone, and shoulder zone. Defects were observed in the mixed zone of the samples exhibiting relatively lower mechanical properties. The highest tensile force was achieved at a plunge rate of 20 mm/min and a rotational speed of 900 rpm. The highest bending force, on the other hand, was obtained at a plunge rate of 30 mm/min and a tool rotational speed of 2100 rpm.

Schlagwörter

Stichwörter der Autor:innen

3D printingfriction stir spot weldingglass fiber-reinforced polylactic acidmechanical properties

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Faculty of Engineering, Zonguldak Bülent Ecevit University, Zonguldak 67100, Türkiye.

ORCID-Profile: Oğuz Koçar, Nergizhan Anaç

Zitieren

APA

Kanlı, E., Koçar, O., & Anaç, N. (2026). An Investigation into the Friction Stir Spot Welding Behavior of 3D-Printed Glass Fiber-Reinforced Polylactic Acid. Polymers, 18(9), 1041. https://doi.org/10.3390/polym18091041

Vancouver

Kanlı E, Koçar O, Anaç N. An Investigation into the Friction Stir Spot Welding Behavior of 3D-Printed Glass Fiber-Reinforced Polylactic Acid. Polymers. 2026;18(9):1041. doi:10.3390/polym18091041

BibTeX
@article{Kanl2026,
  author = {Kanlı, Emre and Koçar, Oğuz and Anaç, Nergizhan},
  title = {An Investigation into the Friction Stir Spot Welding Behavior of 3D-Printed Glass Fiber-Reinforced Polylactic Acid},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {9},
  pages = {1041},
  doi = {10.3390/polym18091041}
}
Kostenlos starten →