EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Comparative Insights Into the Degree of Conversion of a 3D‐Printed Photopolymer Occlusal Splint Resin Fabricated by Stereolithography and Masked Stereolithography Compared to Heat‐Polymerized Acrylics

Izim Turker Kader, Yurdanur Ucar, Pinar Kursoglu

Macromolecular Materials and Engineering · 2025-08 · 310 (8)

DOI: 10.1002/mame.202500185 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Macromolecular Materials and Engineering, online erschienen am 17.06.2025. Verfasst von Izim Turker Kader und 2 weiteren Autor:innen. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The degree of conversion (DC) is a critical determinant of the biocompatibility and long‐term performance of occlusal splints. However, limited evidence exists on how emerging three‐dimensional printing technologies, particularly masked stereolithography (MSLA), affect polymerization efficiency compared to established methods. This study investigated the DC of a photopolymer‐based occlusal splint resin fabricated using stereolithography (SLA) and MSLA technologies, compared to a conventional heat‐polymerized acrylic resin. DC was assessed by Fourier Transform Infrared Spectroscopy (FTIR) at three stages for printed specimens: the unpolymerized resin, after printing and washing (DC Print), and after post‐curing (final DC). The difference between DC Print and final DC (ΔDC) represented the contribution of the post‐curing step. Conventional specimens were evaluated after mixing and after polymerization. The final DC of the conventional group was significantly higher than both SLA and MSLA groups ( p < 0.001), although SLA and MSLA did not differ significantly ( p > 0.05). Post‐curing significantly enhanced polymerization in both printed groups. MSLA printing achieved comparable DC to SLA while reducing production time. These findings support MSLA as a promising and time‐efficient method for splint fabrication, though further improvements in resin formulation and post‐curing protocols are warranted to match the polymerization efficiency of conventional heat‐polymerized acrylics.

Zitieren

APA

Kader, I. T., Ucar, Y., & Kursoglu, P. (2025). Comparative Insights Into the Degree of Conversion of a 3D‐Printed Photopolymer Occlusal Splint Resin Fabricated by Stereolithography and Masked Stereolithography Compared to Heat‐Polymerized Acrylics. Macromolecular Materials and Engineering, 310(8). https://doi.org/10.1002/mame.202500185

Vancouver

Kader IT, Ucar Y, Kursoglu P. Comparative Insights Into the Degree of Conversion of a 3D‐Printed Photopolymer Occlusal Splint Resin Fabricated by Stereolithography and Masked Stereolithography Compared to Heat‐Polymerized Acrylics. Macromolecular Materials and Engineering. 2025;310(8). doi:10.1002/mame.202500185

BibTeX
@article{Kader2025,
  author = {Kader, Izim Turker and Ucar, Yurdanur and Kursoglu, Pinar},
  title = {Comparative Insights Into the Degree of Conversion of a 3D‐Printed Photopolymer Occlusal Splint Resin Fabricated by Stereolithography and Masked Stereolithography Compared to Heat‐Polymerized Acrylics},
  journal = {Macromolecular Materials and Engineering},
  year = {2025},
  volume = {310},
  number = {8},
  doi = {10.1002/mame.202500185}
}
Kostenlos starten →