EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Comprehensive clinical implementation, workflow, and FMEA of bespoke silicone bolus cast from 3D printed molds using open‐source resources

Dean Hobbis iD, Michael D Armstrong, Samir H Patel, Riley C Tegtmeier, Brady S Laughlin, Shadi Chitsazzadeh, Edward L Clouser, Jennifer L Smetanick, Justin Pettit, Justin D Gagneur, Joshua B Stoker, Yi Rong iD und 1 weitere

Journal of Applied Clinical Medical Physics · 2024

DOI: 10.1002/acm2.14498 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Applied Clinical Medical Physics, 2024. Verfasst von Dean Hobbis und 12 weiteren Autor:innen. Beteiligte Einrichtung: Department of Radiation Oncology, Mayo Clinic Arizona, Phoenix, Arizona, USA. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Workflow, Radiotherapy Planning, Computer-Assisted, Silicones. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background

Bolus materials have been used for decades in radiotherapy. Most frequently, these materials are utilized to bring dose closer to the skin surface to cover superficial targets optimally. While cavity filling, such as nasal cavities, is desirable, traditional commercial bolus is lacking, requiring other solutions. Recently, investigators have worked on utilizing 3D printing technology, including commercially available solutions, which can overcome some challenges with traditional bolus.

Purpose

To utilize failure modes and effects analysis (FMEA) to successfully implement a comprehensive 3D printed bolus solution to replace commercial bolus in our clinic using a series of open‐source (or free) software products.

Methods

3D printed molds for bespoke bolus were created by exporting the DICOM structures of the bolus designed in the treatment planning system and manipulated to create a multipart mold for 3D printing. A silicone (Ecoflex 00–30) mixture is poured into the mold and cured to form the bolus. Molds for sheet bolus of five thicknesses were also created. A comprehensive FMEA was performed to guide workflow adjustments and QA steps.

Results

The process map identified 39 and 30 distinct steps for the bespoke and flat sheet bolus workflows, respectively. The corresponding FMEA highlighted 119 and 86 failure modes, with 69 shared between the processes. Misunderstanding of plan intent was a potential cause for most of the highest‐scoring failure modes, indicating that physics and dosimetry involvement early in the process is paramount.

Conclusion

FMEA informed the design and implementation of QA steps to guarantee a safe and high‐quality comprehensive implementation of silicone bolus from 3D printed molds. This approach allows for greater adaptability not afforded by traditional bolus, as well as potential dissemination to other clinics due to the open‐source nature of the workflow.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalWorkflowRadiotherapy Planning, Computer-AssistedSiliconesSoftwareRadiotherapy DosageHumansRadiotherapy, Intensity-Modulated

Stichwörter der Autor:innen

electronsexternal beamprocess mapquality assurancerisk analysis

Substanzen

Silicones

Autor:innen und Institutionen

  • Department of Radiation Oncology, Mayo Clinic Arizona, Phoenix, Arizona, USA.
  • Department of Radiation Oncology, Washington University School of Medicine in St Louis, St Louis, Missouri, USA.
  • University of South Florida Morsani College of Medicine and Tampa General Hospital Cancer Institute.

ORCID-Profile: Dean Hobbis, Yi Rong

Zitieren

APA

Hobbis, D., Armstrong, M. D., Patel, S. H., Tegtmeier, R. C., Laughlin, B. S., Chitsazzadeh, S., Clouser, E. L., Smetanick, J. L., Pettit, J., Gagneur, J. D., Stoker, J. B., Rong, Y., & Buckey, C. R. (2024). Comprehensive clinical implementation, workflow, and FMEA of bespoke silicone bolus cast from 3D printed molds using open‐source resources. Journal of Applied Clinical Medical Physics. https://doi.org/10.1002/acm2.14498

Vancouver

Hobbis D, Armstrong MD, Patel SH, Tegtmeier RC, Laughlin BS, Chitsazzadeh S, et al. Comprehensive clinical implementation, workflow, and FMEA of bespoke silicone bolus cast from 3D printed molds using open‐source resources. Journal of Applied Clinical Medical Physics. 2024. doi:10.1002/acm2.14498

BibTeX
@article{Hobbis2024,
  author = {Hobbis, Dean and Armstrong, Michael D and Patel, Samir H and Tegtmeier, Riley C and Laughlin, Brady S and Chitsazzadeh, Shadi and Clouser, Edward L and Smetanick, Jennifer L and Pettit, Justin and Gagneur, Justin D and Stoker, Joshua B and Rong, Yi and Buckey, Courtney R},
  title = {Comprehensive clinical implementation, workflow, and FMEA of bespoke silicone bolus cast from 3D printed molds using open‐source resources},
  journal = {Journal of Applied Clinical Medical Physics},
  year = {2024},
  doi = {10.1002/acm2.14498}
}
Kostenlos starten →