EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access · CC BY 4.0

Effect of thermal cycling on the mechanical properties of conventional, milled, and 3D-printed base resin materials: a comparative in vitro study

Shuang Xiao, Ruo-Jin Zhang, Fa-Bing Tan

PeerJ · 17.03.2025 · 13 · e19141

DOI: 10.7717/peerj.19141 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift PeerJ, online erschienen am 17.03.2025. Verfasst von Shuang Xiao und 2 weiteren Autor:innen. Beteiligte Einrichtung: College of Stomatology, Chongqing Medical University, Chongqing, China. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Denture Bases, Resins, Synthetic. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Joint Medical Research Project between Chongqing Science and Technology Bureau and Health Commission, Chinese Medical Association and the National Center for the Development of Medical Education, Chongqing College Student Innovation and Entrepreneurship Training Program.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

The purpose of this study is to evaluate the impact of thermal cycling on the mechanical properties of conventional, milled, and 3D-printed denture base materials.

Methods

Unigraphics NX software was used to design the sample data, after which denture base resin samples were fabricated using conventional polymerization (conventional), milling, and 3D-printing techniques. Flexural strength, Vickers hardness, and impact strength of each group of samples were evaluated both before and after 10,000 thermal cycles in distilled water at 5 °C and 55 °C ( n = 8/group). Statistical analysis of the data was conducted using the Kruskal-Wallis H test, Weibull analysis and Spearman correlation analysis.

Results

The flexural strength and impact strength of the 3D-printed group significantly decreased after thermal cycling ( P = 0.001), whereas no significant differences were observed before and after thermal cycling in the conventional or milled groups ( P > 0.05). No significant correlation was found between flexural strength and impact strength for any of the groups. The Weibull modulus of 3D printed groups for both flexural and impact strength decreased after thermal cycling. The Vickers hardness of the conventional group increased significantly after thermal cycling, while Vickers hardness significantly decreased in the milled or 3D-printed groups ( P < 0.05).

Conclusion

Compared with the conventional or milled groups, thermal cycling had a more pronounced effect on the flexural strength, Vickers hardness, and impact strength of the 3D-printed group. These findings indicate that further improvements ( e.g ., material composition, printing parameters and post-processing) in the mechanical properties of 3D-printed materials is necessary before clinical application.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalDenture BasesResins, SyntheticMaterials TestingFlexural StrengthHardnessTemperaturePolymerization

Stichwörter der Autor:innen

3D-printedDenture base materialsMechanical propertiesMilledThermal cycling

Substanzen

Resins, Synthetic

Autor:innen und Institutionen

  • College of Stomatology, Chongqing Medical University, Chongqing, China.
  • Chongqing Key Laboratory of Oral Diseases and Biomedical Sciences, Chongqing, China.
  • Chongqing Medical University Experimental Teaching Management Center, Chongqing Medical University, Chongqing, China.
  • Chongqing Municipal Key Laboratory of Oral Biomedical Engineering of Higher Education, Chongqing, China.

Förderung

  • Joint Medical Research Project between Chongqing Science and Technology Bureau and Health Commission
  • Chinese Medical Association and the National Center for the Development of Medical Education
  • Chongqing College Student Innovation and Entrepreneurship Training Program

Zitieren

APA

Xiao, S., Zhang, R. J., & Tan, F. B. (2025). Effect of thermal cycling on the mechanical properties of conventional, milled, and 3D-printed base resin materials: a comparative in vitro study. PeerJ, 13, e19141. https://doi.org/10.7717/peerj.19141

Vancouver

Xiao S, Zhang RJ, Tan FB. Effect of thermal cycling on the mechanical properties of conventional, milled, and 3D-printed base resin materials: a comparative in vitro study. PeerJ. 2025;13:e19141. doi:10.7717/peerj.19141

BibTeX
@article{Xiao2025,
  author = {Xiao, Shuang and Zhang, Ruo-Jin and Tan, Fa-Bing},
  title = {Effect of thermal cycling on the mechanical properties of conventional, milled, and 3D-printed base resin materials: a comparative in vitro study},
  journal = {PeerJ},
  year = {2025},
  volume = {13},
  pages = {e19141},
  doi = {10.7717/peerj.19141}
}
Kostenlos starten →