EUVIMEDEUVIMED entdecken
Crossref

Effects of post-polymerization conditions on the mechanical properties of 3D-printed dental resin nanocomposite

Keyu Qi, Tamaki Hada, Xiangyu Ren, Maiko Iwaki, Shunsuke Minakuchi, Manabu Kanazawa

Journal of Prosthodontic Research · 2025

DOI: 10.2186/jpr.jpr_d_24_00221 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontic Research, 2025. Verfasst von Keyu Qi und 5 weiteren Autor:innen. Beteiligte Einrichtung: Gerodontology and Oral Rehabilitation, Graduate School of Medical and Dental Sciences, Institute of Science Tokyo, Tokyo Japan. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Nanocomposites, Polymerization, Composite Resins. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 62 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

PURPOSE: To investigate the optimal post-polymerization temperature and time to enhance the mechanical properties of three-dimensional (3D)-printed nanocomposites. METHODS: A control group of pure 3D-printed resin was used to fabricate specimens post-polymerized at 40 °C for 15 min (n = 6). Next, 3-wt% functionalized yttria-stabilized zirconia (YSZ) nanoparticles were dispersed in a 3D-printed resin to fabricate YSZ-based nanocomposites for the experimental groups. The post-polymerization conditions of six experimental groups (n = 6) were set as two temperatures (40 °C and 80 °C) and three time periods (30, 60, and 90 min). The degree of conversion (DC), flexural strength, modulus, fractography, and hardness values of each group were evaluated. One-way and two-way analysis of variance were applied to analyze significant differences among the control and experimental groups and interaction effect of temperature and time of post-polymerization, respectively (α = 0.05). RESULTS: Significant reductions in DC values were noted in the experimental groups compared to the control group. The experimental groups demonstrated significantly higher flexural strengths and moduli than those of the control group. At 80 °C, no significant differences were observed for different post-polymerization times. Compared to post-polymerization at 40 °C, the flexural strength, modulus, and hardness were significantly enhanced when the post-polymerization temperature was increased to 80 °C. CONCLUSIONS: Optimal mechanical properties of 3D-printed YSZ-based nanocomposites could be achieved under post-polymerization at 80 °C and 30 min.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalNanocompositesPolymerizationComposite ResinsDental MaterialsMechanical PhenomenaZirconiumTemperatureHardnessMaterials TestingYttriumFlexural StrengthTime Factors

Stichwörter der Autor:innen

3D printingMechanical propertiesNanocompositesPost-polymerization

Substanzen

Zirconiumzirconium oxideComposite ResinsYttriumDental Materialsyttria

Autor:innen und Institutionen

  • Gerodontology and Oral Rehabilitation, Graduate School of Medical and Dental Sciences, Institute of Science Tokyo, Tokyo Japan.
  • Oral Devices and Materials, Graduate School of Medical and Dental Sciences, Institute of Science Tokyo, Tokyo, Japan.
  • Oral Science Center, Institute of Science Tokyo, Tokyo, Japan.
  • Digital Dentistry, Graduate School of Medical and Dental Sciences, Institute of Science Tokyo, Tokyo, Japan.
  • Clinic of General, Special Care and Geriatric Dentistry, University of Zurich, Zurich, Switzerland.

Zitieren

APA

Qi, K., Hada, T., Ren, X., Iwaki, M., Minakuchi, S., & Kanazawa, M. (2025). Effects of post-polymerization conditions on the mechanical properties of 3D-printed dental resin nanocomposite. Journal of Prosthodontic Research. https://doi.org/10.2186/jpr.jpr_d_24_00221

Vancouver

Qi K, Hada T, Ren X, Iwaki M, Minakuchi S, Kanazawa M. Effects of post-polymerization conditions on the mechanical properties of 3D-printed dental resin nanocomposite. Journal of Prosthodontic Research. 2025. doi:10.2186/jpr.jpr_d_24_00221

BibTeX
@article{Qi2025,
  author = {Qi, Keyu and Hada, Tamaki and Ren, Xiangyu and Iwaki, Maiko and Minakuchi, Shunsuke and Kanazawa, Manabu},
  title = {Effects of post-polymerization conditions on the mechanical properties of 3D-printed dental resin nanocomposite},
  journal = {Journal of Prosthodontic Research},
  year = {2025},
  doi = {10.2186/jpr.jpr_d_24_00221}
}
Kostenlos starten →