EUVIMEDOpdag EUVIMED
Open access · CC BY-NC-ND 4.0

BATTERY MANAGEMENT SYSTEM (BMS) USING ARDUINO UNO FOR BATTERY PROTECTION

Mr. N. Ganesh, G. Mallikarjun, CH. Anand, B. Vikas Reddy, M. Sushanth

International Journal of AI Electrical Civil and Mechanical engineering · 2026-11-17 · 2 (4) · 201-208

DOI: 10.64751/779d2239 ↗

At a glance

Journal article in International Journal of AI Electrical Civil and Mechanical engineering, published online on 2026-11-17. Written by Mr. N. Ganesh and 4 co-authors. The full text is freely available (open access, CC BY-NC-ND 4.0).

AbstractBibliografiske oplysningerCiteRelated studies

Abstract (original language)

Rechargeable lithium-ion batteries now power electric two-wheelers, solar storage units, uninterruptible power supplies, and a wide range of portable equipment. These batteries offer high energy density but are sensitive to overcharge, deep discharge, excessive current, and high temperature, any of which can shorten their life or, in the worst case, lead to swelling, fire, or thermal runaway. Many low-cost battery packs used in student projects and small vehicles have only minimal protection and give the user no information about the condition of the cells. This paper presents a Battery Management System using an Arduino UNO that monitors a series lithium-ion pack, protects it against unsafe conditions, balances the cells, and reports its state to the user. The prototype is built for a four-cell series pack of 18650 lithium-ion cells with a nominal voltage of 14.8 V. Individual cell voltages are measured through precision resistor dividers and an ADS1115 16-bit analog-to-digital converter, pack current is measured with an INA219 sensor over a low-value shunt, and cell temperatures are measured with NTC thermistors attached to the cells. The Arduino UNO processes these readings and controls a pair of back-to-back MOSFETs that disconnect the charger or the load when a limit is exceeded. Protection functions include cell over-voltage cut-off at 4.20 V, cell under-voltage cut-off at 3.00 V, over-current and short circuit protection during discharge, charge current limiting, and over-temperature and under-temperature cut-off. Passive cell balancing is performed by switching bleed resistors across cells whose voltage is higher than the lowest cell by more than a set margin during the final stage of charging. State of charge is estimated by coulomb counting corrected with the open circuit voltage when the pack is at rest, and state of health is estimated from the measured capacity compared with the rated value. Pack data, including cell voltages, current, temperature, state of charge, and fault history, is displayed on an OLED screen and sent through an ESP8266 Wi-Fi module to a cloud dashboard. The user receives alerts when a protection event occurs, when the state of charge falls below a set level, or when a cell shows abnormal behaviour such as faster self-discharge than the others.

Cite

APA

Ganesh, M. N., Mallikarjun, G., Anand, C., Reddy, B. V., & Sushanth, M. (2026). BATTERY MANAGEMENT SYSTEM (BMS) USING ARDUINO UNO FOR BATTERY PROTECTION. International Journal of AI Electrical Civil and Mechanical engineering, 2(4), 201-208. https://doi.org/10.64751/779d2239

Vancouver

Ganesh MN, Mallikarjun G, Anand C, Reddy BV, Sushanth M. BATTERY MANAGEMENT SYSTEM (BMS) USING ARDUINO UNO FOR BATTERY PROTECTION. International Journal of AI Electrical Civil and Mechanical engineering. 2026;2(4):201-208. doi:10.64751/779d2239

BibTeX
@article{Ganesh2026,
  author = {Ganesh, Mr. N. and Mallikarjun, G. and Anand, CH. and Reddy, B. Vikas and Sushanth, M.},
  title = {BATTERY MANAGEMENT SYSTEM (BMS) USING ARDUINO UNO FOR BATTERY PROTECTION},
  journal = {International Journal of AI Electrical Civil and Mechanical engineering},
  year = {2026},
  volume = {2},
  number = {4},
  pages = {201--208},
  doi = {10.64751/779d2239}
}
Start for free →