EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

A Site-Friendly Approach to Assessing Mix Consistency of One-Part Geopolymer Concrete for Extrusion-Based 3D Printing

Prasad Barve, Deep Upadhyaya, Santosh Shah

International Research Journal of Multidisciplinary Technovation · 24.09.2026 · 225-244

DOI: 10.54392/irjmt26514 ↗

Kurz gefasst

Fachartikel in der Zeitschrift International Research Journal of Multidisciplinary Technovation, online erschienen am 24.09.2026. Verfasst von Prasad Barve und 2 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 51 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This work examines the development of an environmentally friendly one-part geopolymer concrete suitable for extrusion-based 3D printing. A total of 27 mixtures were analyzed by systematically varying precursor blends (ground granulated blast-furnace slag (GGBS) and fly ash), aggregate-to-binder ratios, and powdered activator contents. A qualitative "bucket test" was evaluated as a potentially site-friendly consistency-screening technique and showed good agreement with flow-table observations. Within the investigated material and printing conditions, a candidate printability window was associated with zero slump and a slump-flow diameter of 140–180 mm. To balance pumpability with structural build-up, the reduction in slump flow after a 10 min rest period was typically 10–15 mm for the Type-II candidate mixtures. Among the six Type-II candidates, CM-12 (50% GGBS, aggregate-to-binder ratio 1.5, and 10% activator) showed the best overall extrusion and shape-retention response and was used to print a continuous 12-layer object. Printing reduced density by 3.48–8.01% relative to mold casting, while the printed specimens showed a direction-dependent compressive response; no claim of statistically significant anisotropy is made from the available replicate set. The mold-cast mixtures developed 28-day compressive strengths of 32.7–41.29 MPa. The findings support the bucket test as a rapid preliminary screening method rather than a stand-alone predictor of successful printing. Further validation across materials, environmental conditions, and printer configurations is required before the numerical limits can be used as general site-control criteria.

Zitieren

APA

Barve, P., Upadhyaya, D., & Shah, S. (2026). A Site-Friendly Approach to Assessing Mix Consistency of One-Part Geopolymer Concrete for Extrusion-Based 3D Printing. International Research Journal of Multidisciplinary Technovation, 225-244. https://doi.org/10.54392/irjmt26514

Vancouver

Barve P, Upadhyaya D, Shah S. A Site-Friendly Approach to Assessing Mix Consistency of One-Part Geopolymer Concrete for Extrusion-Based 3D Printing. International Research Journal of Multidisciplinary Technovation. 2026:225-244. doi:10.54392/irjmt26514

BibTeX
@article{Barve2026,
  author = {Barve, Prasad and Upadhyaya, Deep and Shah, Santosh},
  title = {A Site-Friendly Approach to Assessing Mix Consistency of One-Part Geopolymer Concrete for Extrusion-Based 3D Printing},
  journal = {International Research Journal of Multidisciplinary Technovation},
  year = {2026},
  pages = {225--244},
  doi = {10.54392/irjmt26514}
}
Kostenlos starten →