EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

One-Part vs. Two-Part Alkali-Activated GGBFS Mortars: Influence of Water-to-Binder Ratio on Extrusion-Based 3D Concrete Printing

Rafaela K. R. Silva, Andreas Appel, Nico Obermeier, Thorsten Stengel, Andrea Kustermann, Paulo H. R. Borges

Infrastructures · 11.11.2026 · 11 (11) · 417

DOI: 10.3390/infrastructures11110417 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Infrastructures, online erschienen am 11.11.2026. Verfasst von Rafaela K. R. Silva und 5 weiteren Autor:innen. Die Arbeit nennt 76 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: CAPES, CNPq, FAPEMIG.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

3D concrete printing (3DCP) offers a transformative approach to industrialized construction and housing solutions. However, its reliance on high Portland cement (PC) mixes raises sustainability concerns. This study explores alkali-activated materials (AAM) as low-carbon alternatives, leveraging an industrial by-product (ground granulated blast furnace slag—GGBFS) to enhance environmental performance of 3DCP mortars. The novelty of this study lies in demonstrating that, despite equivalent activation parameters, one-part (“just-add-water”) and two-part AAM systems exhibit substantially different fresh-state, rheological, and printing behavior in extrusion-based 3DCP—an activation-method-dependent divergence that, to the best of the authors’ knowledge, has not been previously reported. Rheological behavior (dynamic yield stress, plastic viscosity, and structural build-up), flow table spread evolution, hydration kinetics (via isothermal calorimetry), and mechanical performance (cast and extruded specimens of selected mixes) were systematically evaluated. Results reveal that one-part mixes exhibit greater flowability when compared to two-part mixes (140–239 mm vs. 135–210 mm), inferior dynamic yield stress (35.94–93.61 Pa vs. 52.91–152.30 Pa), and slower structural build-up, while maintaining comparable compressive and flexural strengths as the equivalent two-part mortars. These findings demonstrate the potential viability of AAM for extrusion-based 3DCP and highlight the critical influence of activation method and water content on extrudability and performance.

Förderung

  • CAPES
  • CNPq
  • FAPEMIG

Zitieren

APA

Silva, R. K. R., Appel, A., Obermeier, N., Stengel, T., Kustermann, A., & Borges, P. H. R. (2026). One-Part vs. Two-Part Alkali-Activated GGBFS Mortars: Influence of Water-to-Binder Ratio on Extrusion-Based 3D Concrete Printing. Infrastructures, 11(11), 417. https://doi.org/10.3390/infrastructures11110417

Vancouver

Silva RKR, Appel A, Obermeier N, Stengel T, Kustermann A, Borges PHR. One-Part vs. Two-Part Alkali-Activated GGBFS Mortars: Influence of Water-to-Binder Ratio on Extrusion-Based 3D Concrete Printing. Infrastructures. 2026;11(11):417. doi:10.3390/infrastructures11110417

BibTeX
@article{Silva2026,
  author = {Silva, Rafaela K. R. and Appel, Andreas and Obermeier, Nico and Stengel, Thorsten and Kustermann, Andrea and Borges, Paulo H. R.},
  title = {One-Part vs. Two-Part Alkali-Activated GGBFS Mortars: Influence of Water-to-Binder Ratio on Extrusion-Based 3D Concrete Printing},
  journal = {Infrastructures},
  year = {2026},
  volume = {11},
  number = {11},
  pages = {417},
  doi = {10.3390/infrastructures11110417}
}
Kostenlos starten →