EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access · CC BY-NC-ND 4.0

Comparative evaluation of mechanical properties between dual-layer and bonded three-dimensional printed denture base materials: An in vitro study

Naveen Gopi Chander, Aryan Shivaji Deshmukh, Harini Gnana Prakash, Vigneshvar Kandaswamy Srinivasan

The Journal of Indian Prosthodontic Society · 2026

DOI: 10.4103/jips.jips_403_25 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift The Journal of Indian Prosthodontic Society, 2026. Verfasst von Naveen Gopi Chander und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, SRM Dental College, Bharathi Salai, Ramapuram, Chennai, Tamil Nadu, India. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Denture Bases, Dental Materials, Dental Bonding. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 20 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Aim

The study aimed to compare the flexural strength, fracture toughness, and impact strength of the denture base materials fabricated using dual-layer and bonded 3D printing techniques. Settings and Design: In vitro comparative study. Materials and Methods: Seventy-two bar-shaped samples were fabricated using a digital light processing 3D printer and were divided into 2 groups ( n = 36 each). Group I samples were fabricated by dual-layer technique, with the denture base and tooth-colored resins were printed sequentially in a single print cycle. Group II samples were printed separately and bonded with denture base resin. Flexural strength and fracture toughness were tested according to ISO 20795-1:2013, and impact strength was evaluated using ASTM D-256. Statistical Analysis Used: Statistical analysis comprised Shapiro–Wilk for normality, t -test for flexural strength, and Mann–Whitney U -test for fracture toughness and impact strength (α = 0.05).

Results

Group I exhibited significantly higher flexural strength (82.78 ± 2.02 MPa) and fracture toughness (89.91 ± 0.53 MPa) compared to Group II (80.01 ± 2.69 MPa and 86.93 ± 2.29 MPa, respectively). Conversely, impact strength was greater in Group II (4.17 ± 0.39 J) than in Group I (3.00 ± 1.04 J) ( P < .05).

Conclusion

The dual-layer printing technique improved the flexural and fracture resistance of denture base materials by eliminating interfacial weaknesses. Although bonded resins exhibited higher impact strength, the structural advantages of dual-printing support its application in clinical prosthodontics.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalDenture BasesDental MaterialsDental BondingMaterials TestingFlexural StrengthIn Vitro TechniquesHumansDental Stress Analysis

Stichwörter der Autor:innen

Denture base resinSDG 3dual layer printingthree-dimensional-printing

Substanzen

Dental Materials

Autor:innen und Institutionen

  • Department of Prosthodontics, SRM Dental College, Bharathi Salai, Ramapuram, Chennai, Tamil Nadu, India.

Zitieren

APA

Chander, N. G., Deshmukh, A. S., Prakash, H. G., & Srinivasan, V. K. (2026). Comparative evaluation of mechanical properties between dual-layer and bonded three-dimensional printed denture base materials: An in vitro study. The Journal of Indian Prosthodontic Society. https://doi.org/10.4103/jips.jips_403_25

Vancouver

Chander NG, Deshmukh AS, Prakash HG, Srinivasan VK. Comparative evaluation of mechanical properties between dual-layer and bonded three-dimensional printed denture base materials: An in vitro study. The Journal of Indian Prosthodontic Society. 2026. doi:10.4103/jips.jips_403_25

BibTeX
@article{Chander2026,
  author = {Chander, Naveen Gopi and Deshmukh, Aryan Shivaji and Prakash, Harini Gnana and Srinivasan, Vigneshvar Kandaswamy},
  title = {Comparative evaluation of mechanical properties between dual-layer and bonded three-dimensional printed denture base materials: An in vitro study},
  journal = {The Journal of Indian Prosthodontic Society},
  year = {2026},
  doi = {10.4103/jips.jips_403_25}
}
Kostenlos starten →