Development of 3-dimensionally printed denture base material utilizing hybrid polymer: A preliminary investigation
The Journal of Prosthetic Dentistry · 2024
DOI: 10.1016/j.prosdent.2024.07.017 ↗Kurz gefasst
Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2024. Verfasst von Nur A'fifah Husna Zahari und 6 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Dentistry, Universiti Sains Islam Malaysia, Kuala Lumpur, Malaysia. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Denture Bases, Polymethyl Methacrylate, Materials Testing. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 34 Literaturangaben. Gefördert von: Malaysia Ministry of Higher Education.
Abstract (Originalsprache)
STATEMENT OF PROBLEM: Current 3-dimensionally (3D) printed denture bases have inadequate strength and durability for long-term use, and milled denture bases generate excessive waste. Addressing these limitations is crucial to advancing prosthetic dentistry, ensuring improved patient outcomes and promoting environmental responsibility. PURPOSE: The purpose of this in vitro study was to incorporate microparticles into a commercially available 3D printed denture base resin and compare its mechanical and biological properties with the conventional polymethyl methacrylate (PMMA) denture base material. MATERIAL AND METHODS: Microparticles were collected from milled zirconia blanks and were blended with a 3D printing denture base resin (NextDent Denture 3D+). The optimal zirconia microparticle content (2%) for blending and printed was determined by using a liquid-crystal display (LCD) 3D printer. The printed specimens were then postrinsed and postpolymerized based on the manufacturer's instructions. Mechanical and biological characterization were carried out in terms of flexural strength, fracture toughness, and fungal adhesion. One-way ANOVA was carried out to analyze the results statistically. RESULTS: The incorporation of microparticles in the 3D printed denture demonstrated higher mechanical strength (104.77 ±7.60 MPa) compared with conventional heat-polymerized denture base resin (75.15 ±24.41 MPa) (P
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Faculty of Dentistry, Universiti Sains Islam Malaysia, Kuala Lumpur, Malaysia.
- Lecturer, Department of Conservative Dentistry and Prosthodontics, Faculty of Dentistry, Universiti Sains Islam Malaysia, Kuala Lumpur, Malaysia. Electronic address: syafiq.alauddin@usim.edu.my.
- Lecturer, Department of Basic Sciences and Oral Biology, Faculty of Dentistry, Universiti Sains Islam Malaysia, Kuala Lumpur, Malaysia.
- Lecturer, Smart Manufacturing and Advanced Renewable Technology Research Group, Faculty Science and Technology, Universiti Sains Islam Malaysia, Nilai, Malaysia.
Förderung
- Malaysia Ministry of Higher Education
Zitieren
APA
Zahari, N. A. H., Farid, D. A. M., Alauddin, M. S., Said, Z., Ghazali, M. I. M., Lee, H. E., & Zol, S. M. (2024). Development of 3-dimensionally printed denture base material utilizing hybrid polymer: A preliminary investigation. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2024.07.017
Vancouver
Zahari NAH, Farid DAM, Alauddin MS, Said Z, Ghazali MIM, Lee HE, et al. Development of 3-dimensionally printed denture base material utilizing hybrid polymer: A preliminary investigation. The Journal of Prosthetic Dentistry. 2024. doi:10.1016/j.prosdent.2024.07.017
BibTeX
@article{Zahari2024,
author = {Zahari, Nur A'fifah Husna and Farid, Durratul Aqwa Mohd and Alauddin, Muhammad Syafiq and Said, Zulfahmi and Ghazali, Mohd Ifwat Mohd and Lee, Hao-Ern and Zol, Syazwani Mohamad},
title = {Development of 3-dimensionally printed denture base material utilizing hybrid polymer: A preliminary investigation},
journal = {The Journal of Prosthetic Dentistry},
year = {2024},
doi = {10.1016/j.prosdent.2024.07.017}
}
EUVIMED