Stress distribution by parafunctional loading on tooth–implant, implant–implant, and tooth–tooth-supported prosthesis: A comparative three-dimensional finite element analysis
The Journal of Indian Prosthodontic Society · 2024
DOI: 10.4103/jips.jips_30_24 ↗Kurz gefasst
Vergleichsstudie in der Zeitschrift The Journal of Indian Prosthodontic Society, 2024. Verfasst von P Ambili Ravindran und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics and Crown and Bridge, Indira Gandhi Institute of Dental Science, Kothamangalam, Ernakulam, Kerala, India. Hauptthemen laut MEDLINE: Finite Element Analysis, Dental Implants, Dental Prosthesis, Implant-Supported, Imaging, Three-Dimensional. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 29 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar.
Abstract (Originalsprache)
Aim
The study’s objective was to evaluate the stress distribution in tooth-implant, implant-implant, and tooth-tooth supported prostheses under parafunctional loading in axial and oblique directions employing a 3D finite element analysis in the mandibular posterior region which had D3 bone (porous cortical bone and fine trabecular bone). Setting and Design: In vitro study, Finite element analysis. Meterials and Methods: Cone-beam computed tomography data was used by Mimics software (Materialize Mimics 19) to create a three-dimensional finite element simulation of the jaw. Solid Works 2018 (Dassault Systems) was used to produce a geometric 3D model of the three systems. Each model consisted of a bone, an implant, and teeth (Model I tooth-tooth supported, Model II tooth-implant supported and Model III implant-implant supported). The three models’ geometrical models were transferred to Ansys Workbench (19.2 software) for the analysis portion. A load that mimicked masticatory force was delivered in both axial and oblique directions. Statistical Analysis Used: In the present study, statistical analysis was not required because 3D finite element analysis uses deterministic numerical methods to simulate physical behavior and stress distribution patterns.
Result
The results demonstrated that under the parafunctional combined loading process, the implant- implant supported prosthesis showed significantly higher stress concentrations in the bone. It was found that the cortical bone around the crestal region had the highest stresses.
Conclusion
Within the constraints of this investigation, we could draw the following conclusion: Of the three models, the tooth-tooth supported prosthesis exhibited the least amount of stress distribution, which was also least when functional loading was applied in the axial direction.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Department of Prosthodontics and Crown and Bridge, Indira Gandhi Institute of Dental Science, Kothamangalam, Ernakulam, Kerala, India.
- Department of Prosthodontics and Crown and Bridge, Royal Dental College, Thrissur, Kerala, India.
- Department of Mechanical Engineering, Mar Athanasius College of Engineering, Kothamangalam, Ernakulam, Kerala, India.
Zitieren
APA
Ravindran, P. A., Raghavan, R., Christopher, K., Sramadathil, S., George, A., & Sasi, A. K. (2024). Stress distribution by parafunctional loading on tooth–implant, implant–implant, and tooth–tooth-supported prosthesis: A comparative three-dimensional finite element analysis. The Journal of Indian Prosthodontic Society. https://doi.org/10.4103/jips.jips_30_24
Vancouver
Ravindran PA, Raghavan R, Christopher K, Sramadathil S, George A, Sasi AK. Stress distribution by parafunctional loading on tooth–implant, implant–implant, and tooth–tooth-supported prosthesis: A comparative three-dimensional finite element analysis. The Journal of Indian Prosthodontic Society. 2024. doi:10.4103/jips.jips_30_24
BibTeX
@article{Ravindran2024,
author = {Ravindran, P Ambili and Raghavan, Rohit and Christopher, Kiran and Sramadathil, Sethu and George, Ann and Sasi, Athira Kattachirakunnel},
title = {Stress distribution by parafunctional loading on tooth–implant, implant–implant, and tooth–tooth-supported prosthesis: A comparative three-dimensional finite element analysis},
journal = {The Journal of Indian Prosthodontic Society},
year = {2024},
doi = {10.4103/jips.jips_30_24}
}
EUVIMED