EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Biomechanical behavior of all-on-4 concept and alternative designs under different occlusal load configurations for completely edentulous mandible: a 3-D finite element analysis

Ayben Şentürk, Funda Akaltan

Odontology · 2024

DOI: 10.1007/s10266-024-00941-1 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Odontology, 2024. Verfasst von Ayben Şentürk und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Dentistry, Ankara University, Ankara, Turkey. dr.dt.aybensenturk@gmail.com. Hauptthemen laut MEDLINE: Finite Element Analysis, Mandible, Jaw, Edentulous, Dental Prosthesis, Implant-Supported. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The aim of this study was to evaluate the effect of the All-on-4 design and 4 alternative implant-supported fixed prosthesis designs on stress distribution in implants, peri-implant bone, and prosthetic framework in the edentulous mandible under different loading conditions using three-dimensional finite element analysis (3D-FEA).Five different experimental finite element models (Model A (unsplinted 6), Model B (splinted 6), Model C (All-on-4), Model D (axial; 2 anterior, 2 posterior), and Model E (4 interforaminal)) were created. Three different loading conditions were applied (canine loading, unilateral I-loading, and unilateral II-loading). The highest minimum (Pmin) and the maximum (Pmax) principal stress values were acquired for cortical and trabecular bones; the highest von Mises (mvM) stress values were obtained for implants and metal frameworks. Model B and Model D showed the most favorable stress distribution. The All-on-4 design (Model C) also showed acceptable stress values close to those of Model B and Model D in the cortical and trabecular bones. In accordance with the stress values in the bone structure, the lowest stress values were measured in the implants and Co-Cr framework in Model B and Model D. The highest stress values in all structures were measured for unilateral loading- II, while the lowest values were found for canine loading. It was concluded that Model B and Model D experimental models showed better biomechanical performance in all structures. Furthermore, the use of a splinted framework, avoiding cantilevers, results in lower stress transmission. On the other hand, canine loading and unilateral loading-I exhibited the best loading conditions.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Finite Element AnalysisMandibleJaw, EdentulousDental Prosthesis, Implant-SupportedDental Stress AnalysisHumansBiomechanical PhenomenaImaging, Three-DimensionalDental Prosthesis DesignDental ImplantsDenture DesignStress, Mechanical

Stichwörter der Autor:innen

All-on-4Angulated implantsEdentulous mandibleFinite element analysisStress distribution

Substanzen

Dental Implants

Autor:innen und Institutionen

  • Department of Prosthodontics, Faculty of Dentistry, Ankara University, Ankara, Turkey. dr.dt.aybensenturk@gmail.com.
  • Department of Prosthodontics, Faculty of Dentistry, Ankara University, Ankara, Turkey.

Zitieren

APA

Şentürk, A., & Akaltan, F. (2024). Biomechanical behavior of all-on-4 concept and alternative designs under different occlusal load configurations for completely edentulous mandible: a 3-D finite element analysis. Odontology. https://doi.org/10.1007/s10266-024-00941-1

Vancouver

Şentürk A, Akaltan F. Biomechanical behavior of all-on-4 concept and alternative designs under different occlusal load configurations for completely edentulous mandible: a 3-D finite element analysis. Odontology. 2024. doi:10.1007/s10266-024-00941-1

BibTeX
@article{entrk2024,
  author = {Şentürk, Ayben and Akaltan, Funda},
  title = {Biomechanical behavior of all-on-4 concept and alternative designs under different occlusal load configurations for completely edentulous mandible: a 3-D finite element analysis},
  journal = {Odontology},
  year = {2024},
  doi = {10.1007/s10266-024-00941-1}
}
Kostenlos starten →