EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access · CC BY-NC-ND 4.0

Evaluating the impact of print orientation and layer thickness on mechanical properties of three-dimensional-printed denture base resin

Aryan Shivaji Deshmukh, Naveen Gopi Chander, Muthukumar Balasubramanium

The Journal of Indian Prosthodontic Society · 2026

DOI: 10.4103/jips.jips_243_26 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift The Journal of Indian Prosthodontic Society, 2026. Verfasst von Aryan Shivaji Deshmukh und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics and Crown and Bridge, SRM Dental College, Bharathi Salai, Ramapuram, Chennai, Tamil Nadu, India. Hauptthemen laut MEDLINE: Denture Bases, Printing, Three-Dimensional, Acrylic Resins, Resins, Synthetic. Die Arbeit nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Aim

Layer thickness and print orientation are important printing considerations that influence the mechanical performance of additively manufactured denture base resins. However, evidence regarding their combined effects remains limited. The study investigated the influence of print orientation and layer thickness on the flexural strength, fracture toughness, surface roughness, and impact strength of an additively manufactured digital light processing (DLP) denture base resin. Study Setting and Design: In vitro comparative study. Materials and Methods: Using a DLP-based three-dimensional printing system, 384 denture base resin specimens were manufactured with three build orientations (0°, 45°, and 90°) and four printing layer heights (25, 50, 75, and 100 µm). Flexural strength and elastic modulus were assessed using a three point bend test, fracture toughness using a pre-notched three point bending test, and Izod impact tester was used to estimate the impact strength. Surface roughness was evaluated with a stylus profilometer, and fractured surfaces were examined using scanning electron microscopy. Statistical Analysis Used: Two-way analysis of variance and Bonferroni adjusted post hoc comparisons.

Results

Both layer thickness and print orientation significantly influenced all tested properties ( P < .001). The highest flexural strength (127.71 ± 1.83 MPa), fracture toughness (1.49 ± 0.02 MPa·m 0 · 5 ), and impact strength (10.58 ± 0.15 kJ/m 2 ) were observed at 25 µm and 45° orientation, whereas the lowest values were recorded at 100 µm and 90°. Surface roughness increased with increasing layer thickness, with the smoothest surface at 25 µm and 0° (Ra = 0.33 ± 0.01 µm) and the roughest at 100 µm and 90° (Ra = 0.95 ± 0.02 µm).

Conclusion

Fabrication at 25 µm layer thickness and 45° print orientation provided the most favorable mechanical performance for the additively manufactured DLP denture base resin.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Denture BasesPrinting, Three-DimensionalAcrylic ResinsResins, SyntheticSurface PropertiesMaterials TestingFlexural StrengthElastic Modulus

Stichwörter der Autor:innen

Denture base resinsdigital light processing printerslayer height or thicknessprint orientation

Substanzen

Acrylic ResinsResins, Synthetic

Autor:innen und Institutionen

  • Department of Prosthodontics and Crown and Bridge, SRM Dental College, Bharathi Salai, Ramapuram, Chennai, Tamil Nadu, India.

Zitieren

APA

Deshmukh, A. S., Chander, N. G., & Balasubramanium, M. (2026). Evaluating the impact of print orientation and layer thickness on mechanical properties of three-dimensional-printed denture base resin. The Journal of Indian Prosthodontic Society. https://doi.org/10.4103/jips.jips_243_26

Vancouver

Deshmukh AS, Chander NG, Balasubramanium M. Evaluating the impact of print orientation and layer thickness on mechanical properties of three-dimensional-printed denture base resin. The Journal of Indian Prosthodontic Society. 2026. doi:10.4103/jips.jips_243_26

BibTeX
@article{Deshmukh2026,
  author = {Deshmukh, Aryan Shivaji and Chander, Naveen Gopi and Balasubramanium, Muthukumar},
  title = {Evaluating the impact of print orientation and layer thickness on mechanical properties of three-dimensional-printed denture base resin},
  journal = {The Journal of Indian Prosthodontic Society},
  year = {2026},
  doi = {10.4103/jips.jips_243_26}
}
Kostenlos starten →