EUVIMEDEUVIMED entdecken
Crossref

Reinforcement of 3D‐printed resins for denture base by adding aramid fibers: Effect on mechanical, surface, and optical properties

Laura Lourenço Morel iD, Marcus Vinícius Rocha de Almeida iD, Karoline Moraes Dos Santos iD, Maryana Fernandes Praseres iD, Ana Luíza Gonçalves Girundi iD, Larissa Dolfini Alexandrino iD, Wander José da Silva iD

Journal of Prosthodontics · 2026

DOI: 10.1111/jopr.13957 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, 2026. Verfasst von Laura Lourenço Morel und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Oral Rehabilitation, Federal University of Pelotas, Pelotas, Rio Grande do Sul, Brazil. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Denture Bases, Dental Materials, Acrylic Resins. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 52 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

The present study evaluated the mechanical, surface, and optical properties of 3D‐printed resins for removable prostheses reinforced by the addition of aramid fibers. Materials and Methods According to ISO 20795‐1:2013 standards, specimens were printed using a digital light processing 3D printer and divided into two groups ( n = 06/group): 3D‐printed resin for denture base as the control group, and a group with the same 3D‐printed resin in addition of 5% aramid fibers as the experimental group. Red aramid fibers were chosen for aesthetic characterization. The specimens were evaluated for their mechanical properties, such as elastic modulus (GPa), flexural strength (MPa), and superficial properties by their surface microhardness (KHN), surface roughness (μm), and surface free energy (mJ/m 2 ). Optical properties were evaluated by the color difference (∆E00) between groups. The statistical test chosen after the exploratory analysis of the data was One‐way ANOVA followed by Tukey's HSD ( α = 0.05).

Results

The results showed statistical differences in elastic modulus ( p < 0.0001), flexural strength ( p < 0.0001), surface free energy polar variable ( p = 0.0322), total surface free energy ( p = 0.0344), with higher values for the experimental. Surface hardness and surface roughness showed no statistical difference ( p ≥ 0.05). The color difference (∆E00) obtained through the CIEDE2000 calculus was below the perceptibility threshold (≤1.1).

Conclusion

Adding aramid fibers to 3D‐printed resin for denture bases resulted in better mechanical properties, without major alterations in surface properties. In addition, it is an easy‐to‐apply choice for mechanical reinforcement and aesthetic characterization, with the expression of small blood vessels in the 3D‐printed resin for removable denture bases.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalDenture BasesDental MaterialsAcrylic ResinsDenture DesignSurface PropertiesElastic ModulusFlexural StrengthMaterials TestingHardnessColorHumans

Stichwörter der Autor:innen

3D printingcomputer‐aided designdental materialsdenturesmechanical tests

Substanzen

Dental MaterialsAcrylic Resins

Autor:innen und Institutionen

  • Department of Oral Rehabilitation, Federal University of Pelotas, Pelotas, Rio Grande do Sul, Brazil.
  • Department of Prosthodontics and Periodontology, Piracicaba Dental School, University of Campinas, Piracicaba, São Paulo, Brazil.

ORCID-Profile: Laura Lourenço Morel, Marcus Vinícius Rocha de Almeida, Karoline Moraes Dos Santos, Maryana Fernandes Praseres, Ana Luíza Gonçalves Girundi, Larissa Dolfini Alexandrino, Wander José da Silva

Zitieren

APA

Morel, L. L., Almeida, M. V. R., Santos, K. M. D., Praseres, M. F., Gonçalves Girundi, A. L., Alexandrino, L. D., & Silva, W. J. D. (2026). Reinforcement of 3D‐printed resins for denture base by adding aramid fibers: Effect on mechanical, surface, and optical properties. Journal of Prosthodontics. https://doi.org/10.1111/jopr.13957

Vancouver

Morel LL, Almeida MVR, Santos KMD, Praseres MF, Gonçalves Girundi AL, Alexandrino LD, et al. Reinforcement of 3D‐printed resins for denture base by adding aramid fibers: Effect on mechanical, surface, and optical properties. Journal of Prosthodontics. 2026. doi:10.1111/jopr.13957

BibTeX
@article{Morel2026,
  author = {Morel, Laura Lourenço and Almeida, Marcus Vinícius Rocha de and Santos, Karoline Moraes Dos and Praseres, Maryana Fernandes and Gonçalves Girundi, Ana Luíza and Alexandrino, Larissa Dolfini and Silva, Wander José da},
  title = {Reinforcement of 3D‐printed resins for denture base by adding aramid fibers: Effect on mechanical, surface, and optical properties},
  journal = {Journal of Prosthodontics},
  year = {2026},
  doi = {10.1111/jopr.13957}
}
Kostenlos starten →