EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Marginal and internal fit of 3D printed provisional crowns according to build directions

Ji-Eun Ryu iD, Yu-Lee Kim iD, Hyun-Jun Kong iD, Hoon-Sang Chang iD, Ji-Hye Jung iD

The Journal of Advanced Prosthodontics · 2020 · 12 (4) · 225

DOI: 10.4047/jap.2020.12.4.225 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Advanced Prosthodontics, 2020. Verfasst von Ji-Eun Ryu und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, School of Dentistry, Wonkwang University, Iksan, Republic of Korea. Die Arbeit wurde bisher 75-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0). Gefördert von: National Research Foundation of Korea.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

PURPOSE: This study aimed to fabricate provisional crowns at varying build directions using the digital light processing (DLP)-based 3D printing and evaluate the marginal and internal fit of the provisional crowns using the silicone replica technique (SRT). MATERIALS AND METHODS: The prepared resin tooth was scanned and a single crown was designed using computer-aided design (CAD) software. Provisional crowns were printed using a DLP-based 3D printer at 6 directions (120°, 135°, 150°, 180°, 210°, 225°) with 10 crowns in each direction. In total, sixty crowns were printed. To measure the marginal and internal fit, a silicone replica was fabricated and the thickness of the silicone impression material was measured using a digital microscope. Sixteen reference points were set and divided into the following 4 groups: marginal gap (MG), cervical gap (CG), axial gap (AG), and occlusal gap (OG). The measurements were statistically analyzed using one-way ANOVA and Dunnett T3. RESULTS: MG, CG, and OG were significantly different by build angle groups (P

Schlagwörter

Stichwörter der Autor:innen

CrownsDental internal fitDental marginal adaptationPrintingThree-dimensional

Autor:innen und Institutionen

  • Department of Prosthodontics, School of Dentistry, Wonkwang University, Iksan, Republic of Korea.
  • Department of Conservative Dentistry, School of Dentistry, Chonnam National University, Gwangju, Rupublic of Korea.

ORCID-Profile: Ji-Eun Ryu, Yu-Lee Kim, Hyun-Jun Kong, Hoon-Sang Chang, Ji-Hye Jung

Förderung

  • National Research Foundation of Korea

Zitieren

APA

Ryu, J. E., Kim, Y. L., Kong, H. J., Chang, H. S., & Jung, J. H. (2020). Marginal and internal fit of 3D printed provisional crowns according to build directions. The Journal of Advanced Prosthodontics, 12(4), 225. https://doi.org/10.4047/jap.2020.12.4.225

Vancouver

Ryu JE, Kim YL, Kong HJ, Chang HS, Jung JH. Marginal and internal fit of 3D printed provisional crowns according to build directions. The Journal of Advanced Prosthodontics. 2020;12(4):225. doi:10.4047/jap.2020.12.4.225

BibTeX
@article{Ryu2020,
  author = {Ryu, Ji-Eun and Kim, Yu-Lee and Kong, Hyun-Jun and Chang, Hoon-Sang and Jung, Ji-Hye},
  title = {Marginal and internal fit of 3D printed provisional crowns according to build directions},
  journal = {The Journal of Advanced Prosthodontics},
  year = {2020},
  volume = {12},
  number = {4},
  pages = {225},
  doi = {10.4047/jap.2020.12.4.225}
}
Kostenlos starten →